Solar Energy Systems Engineer Interview Questions
For solar engineers designing power and heating systems for homes or businesses. Interviews focus on site surveys, choosing equipment and estimating system performance.
20 questions, ranked by what the job needs most
Print the top 10:Scoring sheetPractice sheet
Question 1: Walk me through how you run a site audit before designing a residential or commercial solar system.
Example answerThe interviewer wants to know whether you collect the site facts a safe, buildable design depends on. Answer as a walk-through in the order you work, and tie each check to a design decision. A sample answer: "Before the visit I pull satellite imagery, utility bills and any plans. On site I start with the roof: age, covering, rafter size and spacing, and signs of sagging or rot, and I photograph the attic framing. Then I measure the usable roof areas, note vents and setbacks, and take a shading reading at each array location. Inside, I check the main panel rating, the main breaker, open spaces and where an inverter and disconnect could go. On one job the panel was too small for the added solar breaker, so we planned a supply-side connection before the proposal went out instead of finding it during the install." Pitfalls to avoid: listing checks without saying why they matter, forgetting the electrical service or the utility's interconnection rules, and implying one fire setback or code edition applies everywhere, since local rules vary.
Interviewer tipStrong answers cover roof structure, shading, the main service panel and utility interconnection, and how findings change the design. Skipping the electrical service check is a red flag.
Candidate tipGo in the order you work on site. Name what you measure or photograph, the structural and electrical items you check, and give one example where a finding changed the design.
Question 2: Walk me through how you design a photovoltaic system for a commercial building, from site data to choosing components.
Example answerThe interviewer wants to hear a clear, ordered design process and the judgment behind each choice. Walk through one real project step by step and explain the tradeoffs. A sample answer: "On a recent office building, I started with a year of utility interval data and the site audit: roof area, structure, shading and the main switchgear. I laid out the array around rooftop equipment and required setbacks, then compared module options by output per square foot and cost. Because part of the roof was shaded in the afternoon, I chose string inverters with independent maximum power point tracking (MPPT) channels, assigning differently shaded strings to separate trackers after checking voltage and current limits. I sized strings for the coldest expected temperature to stay under the inverter's voltage limit, then checked conductor sizing, the point of interconnection and the utility's application requirements. The structural engineer reviewed the added load before we finalized the layout." Pitfalls to avoid: naming equipment brands as if they were the design, skipping code and utility checks, and claiming you handled every discipline alone when others reviewed parts of it.
Interviewer tipLook for a logical sequence: load and roof data, array layout, module and inverter choice, string sizing and code checks. Jumping straight to equipment without site constraints is a red flag.
Candidate tipUse one real project as your thread. Explain each step, the tradeoffs in choosing modules and inverters, and how you checked the design against local code and the utility's rules.
Question 3: How would you guide a solar installation crew that finds the planned conduit route blocked on site?
Interviewer tipA strong answer checks field conditions against the drawings and gives the crew clear instructions. Telling the installers to reroute the conduit without reviewing where it would go is a red flag.
Candidate tipSay what you'd ask the crew to show you about the blocked route for the conduit, the tubing that carries the wiring. Explain what you'd verify against the drawings before giving the crew new instructions.
Question 4: Walk me through a plan you created for developing, monitoring and evaluating a solar energy system.
Example answerThe interviewer wants to see whether you can connect solar system development with a workable plan for monitoring and evaluating its performance.
Use Situation, Task, Action, Result. Identify the project and your planning role. Explain the development stages you laid out, how performance would be measured, who would review the findings, and the plan's actual status or outcome.
Sample answer: "For a warehouse rooftop array, I helped create a plan covering design review, installation, commissioning and performance review. I identified the information needed at each stage and the people responsible for it. For monitoring, I used the modeled output as a starting baseline and specified the production and weather records needed for comparison. I included a review schedule and assigned follow-up of unusual output to the operations lead. The plan gave the project team a common reference for the development stages and the later performance checks."
Pitfalls to avoid: discussing only monitoring software, leaving development milestones out, and setting performance measures without explaining who will review and act on them.
Interviewer tipA strong example connects development milestones with monitoring and evaluation, including an output baseline and responsibility for reviews. Describing only the monitoring software misses the planning work.
Candidate tipChoose one solar project. Explain the development stages, the performance measures and review schedule you planned, who would act on the findings, and what came of the plan.
Question 5: Walk me through a single-line drawing you made in CAD for a solar electric system.
Interviewer tipListen for how the candidate showed the power connections and checked the drawing against the equipment they planned to use. An unexplained mismatch with the equipment list is a red flag.
Candidate tipPick a single-line drawing, a simplified map of power connections, that you made in CAD (computer-aided design) at work or in a capstone project. Trace one connection and name a check you made before sharing it.
Question 6: How do you use an energy production model to compare solar panel layouts on a partly shaded roof?
Interviewer tipListen for how the candidate represents shade in the model and uses the estimated annual production to compare layouts. Changing the weather assumptions between layouts makes the comparison unreliable.
Candidate tipName the modeling software you use and explain how you'd account for shade in each layout. Say which inputs you'd keep the same and how you'd use the annual production estimates to choose a layout.
Question 7: How do you turn a customer's energy goals and site limits into design requirements for a commercial solar project?
Interviewer tipListen for how the candidate turns the customer's energy goal and available space into requirements the design team can check. Promising an output before checking usable space is a red flag.
Candidate tipStart with the customer's energy goal and a site limit, such as usable roof area. Explain how you'd put a measurable production target and that space limit into the design requirements.
Question 8: What would you check in a replacement solar panel's specifications before recommending it for a design that's already underway?
Interviewer tipThe candidate should connect the panel's specifications to the planned layout, inverter limits, and energy output. Recommending a swap based on panel wattage alone is a red flag.
Candidate tipName the specs you'd compare, such as panel size and voltage, and tie them to the layout and the inverter, which converts the panels' power for use. Explain how the swap could affect the design's expected energy output.
Question 9: Share an example of how you improved a checklist for inspecting completed solar installations.
Interviewer tipA strong example names a gap in the solar inspection checklist, the candidate's revision, and its effect on later reviews. Merely adding a sign-off without checking the missed item leaves the gap open.
Candidate tipChoose a real solar inspection checklist you improved. Explain what it failed to cover, how you made that item clear to the inspector, and what changed when the checklist was used.
Question 10: How do you write an installation procedure that makes it clear when solar panel mounts pass inspection?
Interviewer tipA useful procedure ties the mounting checks to the approved installation details and tells the crew what to do if a mount fails. A step that just says 'check the mounts' leaves crews to guess what passes.
Candidate tipPick a mounting check, such as whether the mounts are where the drawings show. Explain how you'd write the pass criteria and tell the crew what to record or do if a mount fails.
Question 11: What is the most challenging part of performing thermal, stress, or cost reduction analyses for solar systems?
Question 12: Tell me about a time you tested or evaluated photovoltaic cells or modules.
Interviewer tipListen for a test method suited to the evaluation, recorded conditions and conclusions supported by results. Calling a module defective without supporting evidence is a red flag.
Candidate tipDescribe the purpose of the cell or module evaluation, the test methods and tools you used, and how you reported the results. A valid result need not include a defect.
Question 13: What factors determine the collector area for an evacuated tube solar hot water system?
Interviewer tipExpect hot water demand, local solar conditions and collector output at the required water temperature. Sizing from roof space alone ignores the heat load.
Candidate tipConnect the building's hot water use to the heat needed, then discuss local sunlight and collector performance at the planned operating temperature. Explain how those inputs affect collector area.
Question 14: Recall a situation where you resolved conflicting site measurements or drawings during a solar engineering audit.
Interviewer tipListen for their own remeasurement or source check, the corrected site record and the effect on the design. Choosing whichever dimension makes the array fit leaves the conflict unresolved.
Candidate tipChoose one solar site audit with conflicting information. Explain the discrepancy, the evidence you checked, the site record you corrected and what the verified information changed.
Question 15: What would you do if a client wanted to judge a new solar system's performance using only its first week of energy production?
Interviewer tipFirst clarify the performance claim and compare production with weather-adjusted expectations. Treating one week's output as proof of annual performance is a red flag.
Candidate tipExplain what one week of solar production can support, the sunlight and operating records you would need, and how you would agree on an evaluation period with the client.
Question 16: Give an example of how you worked with another building designer to resolve a clash with a solar array layout.
Interviewer tipA strong example names the other designer, the competing space needs and the agreed layout change. Moving the array without checking the other system's access or clearance needs is a red flag.
Candidate tipUse one layout conflict. Describe your part in comparing the solar array's space needs with the other system, reaching agreement with its designer and recording the final arrangement.
Question 17: What would you do if an installation crew reported reversed polarity on a PV string just before system start-up?
Interviewer tipKeep the affected PV string out of start-up and have qualified personnel verify polarity using safe test procedures. Energizing it to see whether the inverter rejects it is unsafe.
Candidate tipStart with the instruction you would give the crew about start-up. Then explain how you would arrange safe polarity checks, correction and retesting of the affected PV string.
Question 18: Walk me through a time you caught a mismatch between a solar single-line diagram and its panel schedule before the drawings were issued.
Interviewer tipListen for the circuit or rating mismatch, the cross-check that found it and consistent corrections across both drawings. Issuing a set with a known disagreement leaves the crew with conflicting instructions.
Candidate tipIdentify the mismatch in one drawing set. Explain your check against the panel schedule, your corrections to the CAD drawings and the review that confirmed the set was ready to issue.
Question 19: Describe a time you traced an unexpected PV simulation result to an input error.
Interviewer tipThe example should connect a suspect PV input to the unexpected result and show a checked rerun. Changing loss assumptions just to reach a desired energy forecast is a red flag.
Candidate tipName the unusual simulation result and the input error you found. Focus on how you isolated it, checked the corrected input and confirmed its effect on the PV production forecast.
Question 20: Tell me about a time you challenged a proposed solar equipment substitution because it did not meet the project's design requirements.
Interviewer tipListen for a specific unmet solar design requirement, evidence from the substitute's specifications and the decision on their recommendation. Accepting equipment on price alone misses the technical review.
Candidate tipChoose one proposed solar equipment substitute. Explain the requirement it missed, the specification evidence you used to challenge it and the final decision on the substitution.