Septic Tank Installer Interview Questions
30 questions
Print the top 10:Scoring sheetPractice sheet
Question 1: What checks would you make from the cab before putting a surface mine excavator or loader to work?
What interviewers listen forA sound answer covers warning indicators, control response, and safety devices such as the horn and interlocks, using the machine's startup procedure. Bypassing a faulty interlock is a red flag.
Candidate tipWalk through your in-cab checks in order. Name the indicators and controls you test, how you keep people clear during those checks, and what would keep the machine out of service.
Question 2: Walk me through how you plan a dig before you start, from reading the plans to checking what your machine can safely reach and lift.
Suggested answerThe interviewer wants to see that you plan before you dig, so the work meets the plans and nobody gets hurt. Walk through your steps in order, using a real job if you can.
Sample answer: "First I go over the plans or cut sheets with the foreman so I know the depth, width and grade, and where the spoil and trucks should go. I check that utilities have been located and marked, and I ask about anything that isn't on the plans. Then I walk the area for soft ground, overhead lines and nearby structures. I set the machine on firm, level ground where it can reach the work without stretching out at full reach with a heavy bucket, and I keep the swing area clear or marked off. If we're lifting anything, I check the load against the machine's rating chart. On a sewer trench last year, that walk showed an overhead line near the swing path, so we moved the spoil pile to the other side."
Pitfalls to avoid: skipping the utility check, guessing at machine limits instead of checking the chart or manual, and leaving the foreman out of the plan.
What interviewers listen forStrong answers mention marked utilities, swing radius, firm footing and staying within the machine's rated capacity; starting to dig before checking the plans is a red flag.
Candidate tipUse a real job. Cover reading the plans or cut sheets, checking that utilities are marked, setting the machine where it reaches without overloading, and where spoil and trucks will go.
Question 3: Describe a time you adjusted your bucket movements to reduce spilled material while loading mine haul trucks.
What interviewers listen forListen for the bucket movement they changed and the effect on spillage. An answer about production totals alone does not show control of the loading cycle.
Candidate tipUse one loading job. Describe where material was spilling, the change you made to the bucket movement, and whether it reduced spills into or around the haul truck.
Question 4: Share an example of a problem you caught during a walk-around of an excavator or loader.
What interviewers listen forListen for a specific clue, such as a leak or a loose bucket pin, and what the operator did about it. Continuing to run the machine with a known safety defect is a red flag.
Candidate tipA walk-around is an inspection of the machine from the ground. Point to the part you checked and the wear, leak, or other clue you saw, then say what happened after you raised or addressed the problem.
Question 5: What do you find hardest about following hand signals or reading grade stakes from the cab while digging to plan?
What interviewers listen forA strong answer names a cue that's hard to read from the cab and explains how the operator confirms it. Guessing at an unclear hand signal while moving the bucket is a red flag.
Candidate tipGrade stakes are markers that show the planned height or depth of the cut. Pick a cue you find hard to read from the cab and explain what makes it hard to see and how you confirm it.
Question 6: Tell me about the excavating or loading machines you have run, such as excavators, backhoes, loaders or draglines, and the work you did with them.
Suggested answerThe interviewer wants a clear, honest picture of what you can run and what work you have done, so they can match you to the job. Organize your answer by machine: the type and size, the kind of work, and how much time you have on it. Close with what you are still learning.
Sample answer: "Most of my time has been on mid-size track excavators, mainly digging trenches for water and sewer lines and loading dump trucks. I've also run a rubber-tire backhoe for smaller utility repairs and a wheel loader for loading trucks from stockpiles. I'm comfortable working to grade stakes and with a spotter, and I do a walkaround before every shift. I haven't run a dragline or a large mining shovel yet. When I moved up to a bigger excavator, I learned it by spending time with our lead operator before taking on production work, and I'd expect to do the same here."
Pitfalls to avoid: claiming machines you haven't run, listing machines without saying what work you did with them, and leaving out your safety habits.
What interviewers listen forListen for specific machines matched to specific work and honest limits on what they haven't run; claiming to run everything with no examples is a red flag.
Candidate tipName each machine type and size you have run, the usual work, such as trenching, loading trucks or stripping overburden, and roughly how long you ran each one.
Question 7: Walk me through a job where you operated a machine to backfill an excavation or break up rock or concrete.
What interviewers listen forListen for firsthand details about the bucket or breaker they ran and the work they completed. Flag claims of hands-on experience if their example is limited to watching another operator.
Candidate tipBackfilling means putting material back into an excavation. Name the machine and attachment you ran, such as a bucket or a breaker for rock or concrete, and say what you got done.
Question 8: Share an example of a time you cleared up an unclear instruction about where to dig or place material at a mine.
What interviewers listen forThe example should identify the unclear direction, whom they asked, and how they confirmed the digging or dumping location. Moving material on a guess is a red flag.
Candidate tipChoose one instruction you needed clarified. Explain what was unclear, what you asked the person directing the work, and how the clarification affected the excavation or material placement.
Question 9: Walk me through a time you moved material across a busy mine work area without disrupting truck traffic.
What interviewers listen forExpect a real example of coordinating the machine's route with haul truck movements and a clear result. Relying on truck drivers to dodge the loader is a red flag.
Candidate tipDescribe the material move and the traffic in the work area. Focus on how you chose your route, coordinated with truck drivers, and completed the move.
Question 10: Describe a time you had to control your machine in tough conditions, such as a steep slope, soft ground or a tight trench next to a building.
Suggested answerThe interviewer wants to know that you can run your machine smoothly and safely when the ground or the space works against you. Use Situation, Task, Action, Result: the conditions, how you set up, how you worked the controls, and the result.
Sample answer: "We had to dig a footing trench right next to an existing building, with only a few feet between the tracks and the wall. I set the tracks parallel to the wall, watched the tail swing closely, and asked for a spotter on the building side. I kept the swing short and the bucket low, and I took smaller bites so I wouldn't jerk the machine. Where the ground was soft, we laid mats under the tracks. It took longer than an open dig, but we finished to grade without touching the building."
Pitfalls to avoid: bragging about risky moves, leaving out the spotter or the setup, and ignoring tip-over or swing hazards.
What interviewers listen forLook for careful setup, slow and smooth control, and a spotter where needed; describing risky moves as skill, or ignoring tip-over risk, is a red flag.
Candidate tipDescribe the conditions, how you set up the machine, such as track position, keeping the bucket low or mats under the tracks, how you worked the controls, and how the job turned out.
Question 11: Describe how you handled a problem you spotted while digging, such as a warning light, unstable ground or an unmarked line.
Suggested answerThe interviewer wants to learn whether you notice warning signs while digging and act before a machine problem or ground hazard gets worse.
Build your answer around Situation, Task, Action, Result. Briefly describe the digging work and the sign that caught your attention. Explain your responsibility, then focus on your own actions to secure the machine, alert the foreman and keep the hazard from being ignored. End with the outcome and what you learned.
For example: "A temperature warning came on while I was digging a trench. I stopped digging, lowered the bucket to firm ground and secured the machine according to its operating instructions. I told the foreman which warning had appeared and kept the machine out of use while it was checked. I resumed after it was cleared for use. That experience reminded me to watch the gauges throughout the digging work, even when the machine seems to be running normally."
Avoid describing only what the crew did, suggesting you kept digging despite an unresolved hazard, or leaving out the result.
What interviewers listen forA strong example shows what alerted them, how they stopped digging safely and the result. Continuing to dig with an unresolved hazard is a red flag; ask what they learned.
Candidate tipChoose a real digging problem. Explain the warning you noticed, your own steps to stop work safely and report it, and the outcome. Include what you learned about spotting trouble.
Question 12: Give an example of how you repaired a worn or rutted ramp at a surface mine.
What interviewers listen forA useful example explains how they restored the ramp's surface and checked it before traffic returned. Covering deep ruts without checking the ground beneath them is a warning sign.
Candidate tipPick one ramp repair. Describe the wear, the material you used, the passes you made with the machine, and how you checked the finished surface before vehicles used it.
Question 13: What would you do if you were assigned to clear mud from a pit floor where water had hidden the ground conditions?
What interviewers listen forThe first move should be to have ground conditions and a safe cleanup approach checked with the mine supervisor. Driving into water-covered mud to test its depth is a dangerous first step.
Candidate tipStart with how you would keep the machine out of unverified ground. Explain what you would need to confirm with the mine supervisor before clearing the mud.
Question 14: Tell me about a time you replaced bucket teeth, adjusted tracks or fixed another problem on your machine yourself.
Suggested answerThe interviewer wants to know that you can handle routine repairs on your machine and that you make it safe before you start. Use Situation, Task, Action, Result: what was wrong, how you found it, the steps you took, and how you checked the fix.
Sample answer: "While loading trucks, I noticed the bucket wasn't filling as well and the cutting edge looked uneven. I set the bucket flat on the ground, shut down, took the key and locked the machine out. Two teeth were worn down and one was missing. I drove out the old pins, put in new teeth and pins from the parts box, and checked that each tooth was seated tight. I wrote the change on the daily sheet. The bucket filled better right away, and I told the mechanic the adapters looked worn so they could order new ones."
Pitfalls to avoid: working under a raised bucket, taking on a repair you aren't trained for instead of calling the mechanic, and forgetting to record what you did.
What interviewers listen forStrong answers include lowering attachments, shutting down and locking out, and knowing when to call the mechanic; working under a raised bucket is a red flag.
Candidate tipPick one repair. Explain how you found the problem, how you made the machine safe first, such as lowering the bucket and locking out, and how you checked your work.
Question 15: How do you keep dirt out of grease fittings and joints when lubricating an excavator or loader at a mine?
What interviewers listen forListen for cleaning fittings and the grease gun coupler, using the specified lubricant, and protecting exposed connections. Forcing grease through a dirt-covered fitting risks contaminating the joint.
Candidate tipDescribe how you prepare the fitting and grease gun, check the lubricant, and keep dirt from entering the joint. Include how you keep the coupler clean between grease points.
Question 16: Tell me about a time you went beyond your usual duties to keep a digging or loading job on schedule.
What interviewers listen forLook for reliability that doesn't cut safety corners; staying late is fine, but skipping the walkaround or digging without a spotter to save time is a red flag.
Candidate tipDescribe what was at risk, such as idle trucks or a crew waiting on the trench, what extra you did, and how you kept it safe. End with how the job turned out.
Question 17: Walk me through how you would measure and verify levels of rock or gravel, bases, or other excavated material.
Question 18: Tell me about a time you had to learn to run a machine you hadn't operated before, such as a larger excavator or a dragline.
What interviewers listen forLook for a careful learning plan and respect for the new machine's limits; jumping straight into production work without training or a walkaround is a red flag.
Candidate tipExplain how you learned the controls and limits, such as the operator's manual, time with an experienced operator and starting on easy work, and how long before you were productive.
Question 19: Share an experience in which you successfully coordinated with others. How about a coordination effort that was not as successful?
Suggested answerThe interviewer wants to see how you work with others to line up schedules, tasks, and handoffs, and whether you learn from times it didn't work.
The question asks for two stories, so keep each one short. For the success, explain who was involved, how you kept everyone in step, and the result. For the less successful one, say what went wrong, your part in it, and what you now do differently.
Sample answer: "For an office move, I set up a shared timeline with the facilities, technology, and department leads, and held a 15-minute check-in each week. Everyone was set up and working by Monday morning. Earlier, on a smaller project, I assumed a vendor knew our deadline and didn't confirm it. Their delivery came two days late. Since then I confirm key dates in writing with everyone involved."
Pitfalls: Don't spend all your time on the success. Avoid blaming others for the one that went wrong. Don't skip what you learned.
Question 20: Tell me how you handled a disagreement with a truck driver, spotter or foreman on an excavation job.
What interviewers listen forListen for their own efforts to understand the disagreement and reach a safe resolution, plus what they learned. Ignoring a spotter's stop signal during an argument is a red flag.
Candidate tipUse one real disagreement with a truck driver, spotter or foreman. Briefly set the scene, focus on what you did to work through it, and finish with the result and a lesson you took away.
Question 21: Tell me about the last time you performed routine maintenance on equipment. How did you determine when and what type of work was needed?
Suggested answerThe interviewer wants to see that you keep equipment in good shape on a schedule and can tell when extra care is needed.
Use Situation, Task, Action, Result. Name the equipment and explain how you decided when and what to do, such as the manufacturer's schedule, hours of use, checklists, or warning signs like noise, heat, or leaks. Then describe the work and how it helped.
Sample answer: "I was responsible for weekly maintenance on two forklifts. I followed the schedule in the manual and kept a log of hours and fluid levels. During one weekly check, I noticed the hydraulic fluid was lower than the week before, so I added an inspection of the hoses. I found one starting to crack, tagged the forklift out of service, and replaced the hose before it failed. Keeping the log is what made the change easy to spot."
Pitfalls: Don't describe maintenance as only fixing things after they break. Avoid skipping safety steps such as lockout. Don't forget to explain how you decided what work was needed, since the question asks.
Question 22: Share an example of how you put GPS or laser grade control to use on an excavating machine to improve the work.
What interviewers listen forListen for how they learned the grade control, checked it against stakes or a grade rod and saw a benefit to the digging work. Trusting the display despite a known grade mismatch is a red flag.
Candidate tipPick a real example of learning GPS or laser grade control. Focus on how you used and checked it, the difference it made to your digging work, and what you learned.
Question 23: Provide a time when you dealt calmly and effectively with a high-stress situation.
Suggested answerThe interviewer wants to see how you think and act under pressure, and whether you stay effective when things go wrong.
Use Situation, Task, Action, Result. Set the scene quickly: what made it stressful and what was at stake. Spend most of your answer on what you did: how you steadied yourself, what you dealt with first, and who you told. Close with the outcome and what you would repeat.
Sample answer: "An hour before a client presentation, the file with our final numbers was corrupted. I told the team we had a problem and a plan, split the work so two of us rebuilt the charts from the source data while another person checked them, and let the client know we might start a few minutes late. We started on time, and afterward we set up automatic backups for shared files."
Pitfalls: Don't say you never feel stress. Avoid stories where the stress came from your own avoidable mistake unless you explain what you changed. Don't skip the result.
Question 24: Provide an example of a time when you were able to demonstrate excellent listening skills. What was the situation and outcome?
Suggested answerThe interviewer wants evidence that you listen to understand, not just to reply, and that it makes a difference to your work.
Use Situation, Task, Action, Result. Show what careful listening looked like: letting the person finish, asking follow-up questions, and repeating back what you heard. The outcome should show that listening caught something you would otherwise have missed.
Sample answer: "A manager from another department asked for a monthly report and said they wanted it faster. Instead of starting right away, I asked what they used the report for. They mentioned twice that they only looked at two of the columns. I confirmed that with them, built a one-page summary of just those figures, and it took a third of the time to produce. They used the summary format from then on."
Pitfalls: Don't just describe yourself as a good listener without an example. Avoid an answer where you talk mostly about what you said. Don't leave out the outcome the question asks for.
Question 25: What have you found to be the best way to direct ground workers engaged in activities such as moving stakes or markers, or changing positions of towers?
Question 26: Tell me how you direct workers engaged in placing blocks or outriggers to prevent capsizing of machines when lifting heavy loads. Share an example.
Question 27: Describe a time when you were able to select the best tool to do a job. How did you use reasoning skills to make the best choice?
Suggested answerThe interviewer wants to see how you think through a choice of tool or equipment instead of using whatever is closest.
Use Situation, Task, Action, Result. Describe the job, the options you had, the factors you weighed (safety, the material, precision, time, and cost), and how your choice worked out.
Sample answer: "I needed to drill holes in a set of thin metal brackets without bending them. The quickest option was a hand drill, but it would be hard to keep the holes straight, and the metal could warp. I chose the drill press with a clamp and a bit made for metal, and I used a slower speed and cutting oil. Every hole came out clean and lined up, and none of the brackets had to be redone."
Pitfalls: Don't describe your choice without the reasons behind it. Avoid stories where you skipped safety to save time. Don't forget to say how the choice worked out.
Question 28: What have you found to be the best way to monitor the performance of your work and/or the work of others? Share a time when you had to take corrective action.
Suggested answerThe interviewer wants to know how you track whether work is on target and what you do when it isn't.
Answer both parts. First, describe your method for checking work: what you measure, how often, and how you get feedback. Then give one example of a time you found a problem and corrected it, using Situation, Task, Action, Result.
Sample answer: "I set a few clear checkpoints for any task, such as a draft date and a final review, and compare progress against them each week. On one project, a teammate's section was behind at the draft checkpoint. I asked what was getting in the way and learned they were waiting on data from another team. I followed up with that team, got the data the next day, and we moved the review back two days. The project still finished on time."
Pitfalls: Don't describe constant checking that sounds like micromanagement. Avoid blaming the person who fell behind. Don't skip the corrective action.
Question 29: Provide a time when you worked in a rapidly evolving workplace. How did you deal with the change?
Suggested answerThe interviewer wants to know how you respond when processes, tools, or priorities change quickly, and whether you help or slow things down.
Use Situation, Task, Action, Result. Describe what was changing and how it affected your work. Then explain what you did to adjust: learning the new way, asking questions, or helping others through it. End with how things turned out and what you took from it.
Sample answer: "In one year my team changed its scheduling software, its reporting process, and its manager. When the new software came in, I signed up for the first training session, wrote a one-page guide for the steps we used most, and shared it with the team. Questions to our manager dropped within a couple of weeks, and I was asked to help test the next update."
Pitfalls: Don't complain about the changes or past leadership. Avoid saying you just went along with it; show what you actively did. Don't pick a change so small it doesn't show adaptability.
What interviewers listen forMake sure the candidate is flexible.
Candidate tipShow that you can adapt.
Question 30: Share an example of a time you had to gather information from multiple sources. How did you determine which information was relevant?
Suggested answerThe interviewer wants to know how you collect information and how you decide what to trust and use.
Use Situation, Task, Action, Result, and spend most of your answer on the second part of the question. Explain what sources you used, how you checked them against each other, and what rule you used to decide what mattered, such as how current it was or how closely it fit the question.
Sample answer: "My manager asked me to recommend a new supplier for office equipment. I collected price lists from four suppliers, read online reviews, and asked two other departments about their experience. Some reviews were several years old, so I gave more weight to recent ones and to my colleagues' first-hand accounts. I summarized the top two options in a one-page comparison, and we chose the supplier that scored best on reliability and price."
Pitfalls: Don't list sources without explaining how you filtered them. Avoid saying you used everything you found. Don't forget to say what decision the information supported.