Avionics Technician Interview Questions
For avionics technicians who service onboard aircraft electronics. Interviews focus on setting up test equipment and finding faults in radios and navigation systems.
30 questions, ranked by what the job needs most
In other fields: Electrical and Electronics Repairers, Commercial and Industrial Equipment · Aerospace Engineering and Operations Technicians · compare them →
Print the top 10:Scoring sheetPractice sheet
Question 1: What would you do if the spare avionics unit had a different part number from the failed unit you were replacing?
Interviewer tipA strong answer checks the approved parts data for the aircraft's configuration before fitting the spare. Assuming a different part number is interchangeable because the unit fits is a red flag.
Candidate tipStart with how you'd confirm whether the different part number is an approved replacement for this aircraft. Explain what you'd do if you could not verify that before fitting the spare.
Question 2: Tell me how you traced and fixed a fault that made an aircraft radio cut in and out.
Interviewer tipListen for how they narrowed the fault to the radio, wiring, or antenna and checked that the fix held. Calling it fixed after one clear transmission without checking the original conditions is a red flag.
Candidate tipStart with when the radio cut out. Walk through how you narrowed the cause, what you fixed, and how you checked the radio under the conditions that brought on the fault.
Question 3: Give an example of how you used a voltmeter or an oscilloscope to track down a fault in an avionics unit on the bench.
Interviewer tipListen for where they measured, the reading they expected, and how the reading narrowed the fault. A red flag is calling a part bad without knowing what a normal reading should be.
Candidate tipSay what reading you expected and what the actual reading told you about the circuit. An avionics training lab is fine, and an oscilloscope is a tool that shows how an electrical signal changes over time.
Question 4: Share an example of setting up ground test equipment to check avionics on a parked aircraft.
Interviewer tipListen for a check that confirmed the setup was ready, such as a self-check on the test equipment where available. Trusting the readings before confirming the connections and settings is a red flag.
Candidate tipName the equipment and the aircraft system you were checking. Describe the connections and settings you checked and how you knew the test equipment was ready to use.
Question 5: Describe a time you repaired or bench-tested a faulty avionics unit, such as a radio, transponder or display, and got it working again.
Example answerThe interviewer wants proof that you can find and fix a fault in an electronic unit and show that it works. Use Situation, Task, Action, Result: the unit and its symptom, your role, the tests and repair, and how you confirmed it met specs. For example: "A transponder came to the shop with a report of weak replies, and I was assigned to troubleshoot it on the bench. I followed the component maintenance manual, connected the unit to the test set, and found the output power was below the limit. Using the manual's fault isolation steps, I traced it to a failed component in the output stage, replaced it, and reran the full test procedure. Every reading was within limits, so I recorded the results and returned the unit to stock." Pitfalls to avoid: skipping the test that proved the repair, claiming repairs beyond what your shop or role allows, and leaving out the documentation you followed.
Interviewer tipListen for a clear fault description, the test steps and equipment they used, and how they confirmed the repair against the specs; replacing parts until the fault goes away is a red flag.
Candidate tipDescribe the symptom, how you isolated the fault to a component, the repair, and the test you ran to prove it met specs. Mention the documentation you followed.
Question 6: How do you check whether a proposed avionics repair is allowed for the aircraft you're working on?
Interviewer tipA strong answer checks that the repair instructions apply to the aircraft and its equipment. Using instructions from a similar aircraft without checking that they apply is a red flag.
Candidate tipName the maintenance manual or other approved repair instructions you'd check. Explain how you confirm they apply to that aircraft and what you do if they don't cover the repair.
Question 7: How do you keep aircraft maintenance records clear and complete after an avionics repair?
Interviewer tipA good entry lets the next technician see what was reported, what work was done, and what the check showed. Marking the job complete without recording the work leaves a gap in the maintenance history.
Candidate tipWalk through a typical maintenance entry. Explain how you record the reported fault, the work performed, and the result of the check after the repair.
Question 8: Walk me through a time you planned where to mount avionics equipment and route its wiring in an aircraft.
Interviewer tipListen for how they used the drawings to check fit and access, such as leaving room to reach a connector. Picking a wire route without checking clearance is a red flag.
Candidate tipExplain how the installation drawings and the space in the aircraft shaped your layout. Say how you knew the equipment and wiring would fit and still be reachable for service.
Question 9: Describe a time you fitted and connected a new or replacement avionics unit in an aircraft.
Interviewer tipListen for the checks they made on the mounting and connectors. A candidate who relies on power-up alone has missed whether the unit is secure.
Candidate tipPick one unit and explain your part in securing it and checking its connections. Close with the result of the check after installation.
Question 10: Tell me about a time a careful inspection of wiring, connectors or antennas helped you find the cause of an avionics problem.
Example answerThe interviewer wants to see that you inspect carefully before you replace parts. Use Situation, Task, Action, Result: the symptom, what you were asked to do, how you inspected and what you found, and the fix. For example: "Crews reported static on one communication radio, but the radio tested fine on the bench. I was asked to look at the aircraft side. I followed the wiring diagram from the radio rack to the antenna, checking each connector and the harness along the way. At the antenna I found corrosion on the connector and a cracked seal that was letting in water. I replaced the connector as the manual called for, resealed the antenna, and ran an operational check. The static was gone, and I documented the repair." Pitfalls to avoid: leaving out the order you inspected things in, making it sound as if you found the problem by luck, and skipping the test that confirmed the fix.
Interviewer tipListen for a methodical inspection, such as checking for chafing, corrosion or loose pins, and how they confirmed the finding before repairing it; guessing without inspecting is a red flag.
Candidate tipDescribe the symptom, what you inspected and in what order, what you found, and how you confirmed it caused the problem. End with the fix and the follow-up test.
Question 11: Share an experience in which you effectively coordinated work with engineers, technicians, and/or other aircraft maintenance personnel.
Question 12: Provide an experience in which you accurately interpreted flight test data and diagnosed a malfunction or systemic performance problem.
Question 13: Share an experience in which your attention to detail and thoroughness had an impact on your last company.
Example answerThe interviewer wants proof that you catch errors others miss and that this protects the organization.
Use Situation, Task, Action, Result. Describe what you were checking, what you noticed, and how you found it, such as comparing against a source or double-checking totals. Then explain what would have happened if the error had gone through, and what you did to prevent it next time.
Sample answer: "While preparing an order for a large customer, I compared the quantities against the signed quote, as I always do, and saw that one item had been entered as 1,000 units instead of 100. I flagged it to my supervisor, we corrected it before it shipped, and we avoided a costly return. Afterward I suggested adding a quote-check step to the order form, and the team adopted it."
Pitfalls: Don't just say you're detail-oriented without an example. Avoid exaggerating the dollar impact. Don't describe perfectionism that caused missed deadlines.
Question 14: Provide an example when your ethics were tested.
Example answerThe interviewer wants to know whether you do the right thing when it is inconvenient, and how you handle pressure to cut corners.
Use Situation, Task, Action, Result. Describe the pressure or temptation without naming people, explain the choice you made and why, and how you handled the conversation. Keep the focus on your actions, not on judging others.
Sample answer: "Near the end of a quarter, a coworker asked me to record a sale as complete even though the customer hadn't signed yet, so our numbers would look better. I told them I wasn't comfortable doing that and suggested we tell our manager the deal would close the following week. My manager agreed it should wait. The customer signed early in the new quarter, and our records stayed accurate."
Pitfalls: Don't say your ethics have never been tested. Avoid stories that make you sound self-righteous or that share confidential details. Don't pick an example where you went along with the wrong choice and stop there.
Question 15: Describe an experience in which you effectively connected a component to an assembly.
Question 16: Share an experience in which you used hand tools and/or soldering irons to assemble components.
Question 17: Tell me how you prioritize when several avionics write-ups are open on aircraft that are all due to fly soon.
Example answerThe interviewer wants to see how you set priorities when time is short and safety is involved. Explain the order you use, then show it with a real shift. Airworthiness is a requirement. Set priorities within that requirement, using departure times and available people and parts. For example: "On one night shift, three aircraft had open avionics write-ups and all were due out in the morning. I sorted them first by what would keep an aircraft on the ground, then by departure time. One radio fault looked like it could be deferred under the operator's approved procedures, so I raised it with maintenance control rather than deciding on my own. I worked the grounding item on the first departure, checked that parts were on hand for the second, and kept my lead updated so they could move people if needed. I recorded the work status and handed the unresolved items to maintenance control for authorized decisions." Pitfalls to avoid: promising every aircraft on time, making deferral decisions outside your role, and describing a plan without a real example.
Interviewer tipStrong answers put airworthiness first, then the schedule, and show they talk with the lead or maintenance control; promising every aircraft on time without checking parts or staffing is a red flag.
Candidate tipExplain how you sort items by what grounds the aircraft and what may be deferred under the operator's approved procedures, then by departure time. Use a real shift as the example.
Question 18: Describe how you chose the relevant information from pilot reports, wiring diagrams, manuals and fault history while troubleshooting a real avionics fault.
Example answerThe interviewer wants to see how you collect and weigh information before you touch the aircraft. Use Situation, Task, Action, Result: the fault, your role, the sources you compared and how you selected the information that guided your checks. For example: "When a crew reported that the autopilot disconnected in turbulence, I started with their write-up and asked the pilot what they saw. Then I pulled any fault codes the system had stored and checked the aircraft's history for past entries on the same system. Two earlier write-ups mentioned the same disconnect. With the wiring diagram and the manual's fault isolation steps, I listed the sensors and connections that could cause it and began with the one that showed up in both the codes and the history. That led me to a loose sensor connector." Pitfalls to avoid: jumping straight to replacing parts, ignoring the crew's description or past write-ups, and naming sources without saying how you used them.
Interviewer tipListen for how they weighed the pilot's report, applicable manual and aircraft history in one real fault. Choosing a manual without checking that it applies to the aircraft is a red flag.
Candidate tipUse a real fault as your example. Say which sources you checked, what each one told you, and how together they pointed you to the likely cause.
Question 19: Walk me through a scheduled avionics check you performed using the aircraft's inspection program and maintenance records to identify the work due.
Example answerThe interviewer wants to know that you plan scheduled work from the approved program and the records, not from memory. Use Situation, Task, Action, Result for one scheduled check: the work due, your role, how the program and records guided your maintenance, and what you documented. For example: "On a scheduled check, I was issued task cards drawn from the aircraft's inspection program. Before starting, I reviewed the maintenance records for open entries and deferred items on the avionics systems, and found a deferred radio write-up that could be cleared during the check. I grouped tasks by area so I wasn't opening the same panels twice, and made sure the test equipment I needed was in calibration. As I finished each task, I signed off what my role allowed and noted any findings for the lead." Pitfalls to avoid: describing maintenance done without the required authorization or applicable instructions, skipping the records review, and leaving out how you documented the work.
Interviewer tipA strong answer names the inspection program or task cards, checking records for due items and open entries, and confirming anything unclear with a lead; working from memory alone is a red flag.
Candidate tipDescribe a real scheduled check: where the due items came from, how you reviewed the records, and how you planned and documented the work.
Question 20: Tell me about a time you learned a new avionics system or software update and used that knowledge to get an aircraft back in service.
Interviewer tipListen for how they learned it, such as manufacturer training, the manual or a service bulletin, and checked their understanding before working on the aircraft; learning by trial on a live aircraft is a red flag.
Candidate tipName the kind of system and how you learned it, then describe the job where you first used it. Say what you checked to be sure the work was right, and what it saved the crew or the shop.
Question 21: Share an experience in which you conducted a test of a product, service, or process and successfully improved the quality or performance.
Example answerThe interviewer wants evidence that you test things carefully and use what you find to make them better.
Use Situation, Task, Action, Result. Explain what you tested and why, how you set up the test, what the results showed, and what you changed. End with how you measured the improvement.
Sample answer: "Customers kept saying our online order form was confusing, so I was asked to look into it. I had five coworkers who had never used the form place a test order while I watched and took notes. Four of them got stuck on the same shipping step. I suggested moving that step and rewording two labels, then ran the same test again. All five finished without help, and complaints about the form dropped over the next month."
Pitfalls: Don't describe a change made on a hunch with no test. Avoid skipping how you checked the result. Don't use jargon without explaining it.
Question 22: Tell me about your last experience doing repair work. How did you determine what tools you needed?
Example answerThe interviewer wants to see how you plan a repair, including choosing the right tools, so the job is done safely and well.
Use Situation, Task, Action, Result. Describe the repair, how you figured out what was wrong, how you decided on tools and parts (the manual, the fasteners involved, what you saw during inspection), and how the repair turned out.
Sample answer: "A door closer at our building's entrance was letting the door slam. I checked the manual for that model and learned the speed valves needed a small hex key, and that a leaking closer would need replacing instead. I looked for oil around the body, saw none, and brought the hex key, a step ladder, and a rag. I adjusted the closing and latch speeds a little at a time and tested the door after each turn. It closed smoothly, and I noted the settings in our maintenance log."
Pitfalls: Don't describe grabbing whatever tool was nearby. Avoid skipping how you tested the repair. Don't forget to answer the tools part of the question.
Question 23: Describe a time when you were able to select the best tool to do a job. How did you use reasoning skills to make the best choice?
Example answerThe interviewer wants to see how you think through a choice of tool or equipment instead of using whatever is closest.
Use Situation, Task, Action, Result. Describe the job, the options you had, the factors you weighed (safety, the material, precision, time, and cost), and how your choice worked out.
Sample answer: "I needed to drill holes in a set of thin metal brackets without bending them. The quickest option was a hand drill, but it would be hard to keep the holes straight, and the metal could warp. I chose the drill press with a clamp and a bit made for metal, and I used a slower speed and cutting oil. Every hole came out clean and lined up, and none of the brackets had to be redone."
Pitfalls: Don't describe your choice without the reasons behind it. Avoid stories where you skipped safety to save time. Don't forget to say how the choice worked out.
Question 24: Provide an example of a time when you were able to demonstrate excellent listening skills. What was the situation and outcome?
Example answerThe interviewer wants evidence that you listen to understand, not just to reply, and that it makes a difference to your work.
Use Situation, Task, Action, Result. Show what careful listening looked like: letting the person finish, asking follow-up questions, and repeating back what you heard. The outcome should show that listening caught something you would otherwise have missed.
Sample answer: "A manager from another department asked for a monthly report and said they wanted it faster. Instead of starting right away, I asked what they used the report for. They mentioned twice that they only looked at two of the columns. I confirmed that with them, built a one-page summary of just those figures, and it took a third of the time to produce. They used the summary format from then on."
Pitfalls: Don't just describe yourself as a good listener without an example. Avoid an answer where you talk mostly about what you said. Don't leave out the outcome the question asks for.
Question 25: Share an experience in which you successfully shared a difficult piece of information.
Example answerThe interviewer wants to see that you can deliver bad or sensitive news clearly, honestly, and with respect.
Use Situation, Task, Action, Result. Describe what the news was and who needed to hear it. Explain how you prepared, when and how you told them, and what next steps you offered. End with how they responded.
Sample answer: "I had to tell a client that their project would be two weeks late because a part we needed was back-ordered. I called them as soon as I knew, rather than waiting for the weekly update. I explained the cause, gave the new date, and offered two options: wait for the part, or use a slightly different one that was in stock. They chose the alternative, and the project finished only a few days late."
Pitfalls: Don't pick news that wasn't really difficult. Avoid a story where you put off the message. Don't blame others while delivering the news.
Interviewer tipMake sure that the candidate has open lines of communication.
Candidate tipThe employer wants to ensure you have open communication with those you work with.
Question 26: Share an example of when you went above and beyond the "call of duty".
Interviewer tipLook for answers that show the candidate is dependable.
Candidate tipThe employer wants to know that you are dependable.
Question 27: How do you balance cooperation with others and independent thinking? Share an example.
Example answerThe interviewer wants to see that you can work well with a team while still bringing your own judgment, and that you know when to speak up and when to go along.
Start with a short answer about how you balance the two, then give one example. A good example shows you sharing your own view, listening to others, and then supporting the team's decision even if it wasn't yours.
Sample answer: "I try to form my own view first, share it clearly, and then commit to whatever the group decides. On one project, the team wanted to launch a new form right away. I thought we should test it with a few users first and explained why. We agreed on a one-week trial. Testing found a confusing field, we fixed it, and the full launch went smoothly."
Pitfalls: Don't present yourself as someone who always goes along or always insists on your own way. Avoid a story where you ignored the team's decision. Don't skip the example.
Interviewer tipTry to determine if the candidate has a cooperative attitude or is otherwise good-natured.
Candidate tipThe employer wants to know that you have a cooperative attitude or are otherwise good-natured.
Question 28: Provide a time when you dealt calmly and effectively with a high-stress situation.
Example answerThe interviewer wants to see how you think and act under pressure, and whether you stay effective when things go wrong.
Use Situation, Task, Action, Result. Set the scene quickly: what made it stressful and what was at stake. Spend most of your answer on what you did: how you steadied yourself, what you dealt with first, and who you told. Close with the outcome and what you would repeat.
Sample answer: "An hour before a client presentation, the file with our final numbers was corrupted. I told the team we had a problem and a plan, split the work so two of us rebuilt the charts from the source data while another person checked them, and let the client know we might start a few minutes late. We started on time, and afterward we set up automatic backups for shared files."
Pitfalls: Don't say you never feel stress. Avoid stories where the stress came from your own avoidable mistake unless you explain what you changed. Don't skip the result.
Question 29: Provide an experience in which you effectively fabricated parts and/or test aids.
Question 30: Describe your experience operating computer-aided drafting and design applications.
New to interviews? Start with the common questions every interview asks →