Wind Turbine Service Technician Interview Questions
For technicians who maintain and repair wind turbines. Interviews focus on diagnosing generator and control faults, testing electrical parts and servicing equipment on towers.
20 questions, ranked by what the job needs most
Print the top 10:Scoring sheetPractice sheet
Question 1: Walk me through how you diagnosed a wind turbine generator problem that first showed up as an alarm.
Interviewer tipListen for the readings or tests the technician used to confirm the cause. Treating the alarm alone as proof that the generator failed is a red flag.
Candidate tipStart with the alarm and the turbine's operating readings. Explain which check you made to narrow down the problem and what confirmed the cause.
Question 2: Tell me about a wind turbine pitch fault you fixed when a blade wouldn't reach the angle the controls called for.
Interviewer tipListen for the observation or test that narrowed down the cause and a check that the blade reached the requested angle after the repair. Returning the turbine to service without testing blade movement is a red flag.
Candidate tipBlade pitch is the angle of a turbine blade. Describe the clue that helped you find the fault, what you repaired, and how you checked that the blade reached the requested angle afterward.
Question 3: How do you carry out routine maintenance on wind turbine equipment?
Interviewer tipExpect the turbine's service instructions, safe isolation, scheduled inspection and servicing, and recorded findings. Signing off maintenance that was not done is a red flag.
Candidate tipWalk through preparation, safe isolation, inspection and scheduled service using the turbine's maintenance instructions. Explain the checks you make and how you record completed work and faults needing follow-up.
Question 4: How do you test electrical components in wind systems safely with equipment suited to the fault?
Interviewer tipExpect a test plan, suitable instruments, safe isolation and verification of de-energization for tests that require it. Using resistance mode on an energized circuit is a red flag.
Candidate tipUse a wind-system component to explain your method. Cover the fault, instrument choice, safe test conditions and interpretation of readings. Distinguish tests requiring isolation from authorized energized measurements.
Question 5: What would you do if a wind turbine tripped again during its first restart after a repair?
Interviewer tipThe restart should stop while the trip is checked against the repair and restart procedure. Repeated resets or bypassing a protective trip to keep the turbine running are red flags.
Candidate tipStart with how you would keep the turbine stopped safely. Then explain how you would use the trip information and restart procedure to decide whether another start is safe.
Question 6: How do you carry out a wind turbine system test using a written test plan?
Interviewer tipExpect checks of the plan's scope, safe test setup, required readings, and acceptance limits. Changing test steps without resolving the change with the engineer or test lead is a red flag.
Candidate tipTake the test from preparation through recording the results. Explain how you follow the plan's sequence and limits, including what you do when a step cannot be completed as written.
Question 7: Share an example of a time you caught a problem in turbine data you were collecting for testing or analysis.
Interviewer tipListen for a specific data problem, the checks they made, and how they kept bad readings out of the test or analysis. Silently changing readings to fit expectations is a red flag; ask what they learned.
Candidate tipUse one real collection problem, such as missing readings or mismatched timestamps. Focus on how you spotted it, checked the source, and supplied usable turbine data or clearly marked its limits.
Question 8: Walk me through a time you corrected a wind turbine parts record that showed a replacement component was on hand when it was missing.
Interviewer tipThe example should show stock checks, a search through parts issue records, and notice to the lead about the shortage. Adjusting the record without investigating where the component went is a red flag.
Candidate tipChoose a real missing turbine component and explain how you checked its part number, storage location, and issue records. Focus on your correction to the parts record and its effect on the repair.
Question 9: Describe your experience staying comfortable and focused while working at height on wind turbine towers or similar structures.
Interviewer tipListen for a specific work or training example showing focus and sound judgment at height. Continuing tower work after losing the ability to work safely is a red flag; avoid questions about medical conditions.
Candidate tipUse a tower climb or similar work-at-height experience, including training. Describe the setting, how you stayed focused on the work and the outcome. Keep the answer about work experience rather than health history.
Question 10: Share an example of a time you taught another technician a wind turbine testing procedure.
Interviewer tipListen for the candidate's own teaching steps and evidence the technician could carry out the test safely. Assuming understanding without checking it is a red flag; ask what they would change.
Candidate tipPick one test you taught. Explain the technician's starting knowledge, how you demonstrated the procedure, and how you checked that they could perform it.
Question 11: Tell me about the last time you inspected or repaired fiberglass turbine blades.
Question 12: Share an example when you assisted in assembly of individual wind generators or construction of wind farms.
Question 13: Describe an experience when you operated manufacturing equipment to fabricate wind turbines.
Question 14: Give an example of how you confirmed a wind turbine converter repair had fixed the fault.
Interviewer tipListen for the converter fault, the candidate's own checks against repair instructions, and evidence it stayed resolved. Declaring success just because the alarm cleared is a red flag; ask what they learned.
Candidate tipChoose one converter repair. Briefly describe the fault, then focus on the checks you personally made after the repair, the results, and anything you would check differently next time.
Question 15: Describe a time you found unexpected wear during scheduled wind turbine maintenance.
Interviewer tipA strong case shows how they assessed the worn turbine part, checked service limits, and arranged follow-up. Dismissing wear without checking its extent is a red flag; ask how the finding changed the service work.
Candidate tipName the turbine part and the wear you found. Explain your checks, how you decided what needed attention, and the outcome of the maintenance visit.
Question 16: What can insulation resistance readings tell you about a wind turbine generator's windings?
Interviewer tipExpect insulation condition, temperature or moisture effects, and comparison with test limits or earlier readings. Treating one high reading as proof the generator has no faults is a red flag.
Candidate tipExplain what the readings suggest about winding insulation. Include temperature or moisture effects and comparison with the generator's test instructions or earlier results; distinguish insulation health from a complete generator diagnosis.
Question 17: Share an example of a time a multimeter setup gave you a misleading reading on a wind turbine electrical component.
Interviewer tipListen for how they checked the meter settings, leads, or connections and confirmed the corrected reading. Replacing a turbine component on a suspect reading without checking the setup is a red flag; ask what they changed afterward.
Candidate tipUse one real multimeter setup problem. Explain the reading that made you question it, your safe checks of the setup, and how the corrected measurement affected your conclusion about the turbine component.
Question 18: What checks do you make before starting a wind turbine after scheduled maintenance?
Interviewer tipExpect completed-work clearance, people and tools clear, guards restored, and release of energy controls by the required procedure. Starting while a technician's lock remains in place is a red flag.
Candidate tipWork through the turbine's pre-start checks in order. Cover maintenance completion, crew clearance, equipment readiness, and the required release of energy controls before a start.
Question 19: What would you do if your fall-protection equipment failed its inspection before a wind turbine tower climb?
Interviewer tipThe climb should wait while failed fall-protection gear is removed from use, reported, and replaced with inspected equipment. Using damaged gear for a short climb is a red flag.
Candidate tipStart with keeping the climb on hold. Explain how you would keep the failed gear out of use, report the defect, and confirm replacement equipment is safe before climbing.
Question 20: Talk about a time you kept shared wind turbine service tools accounted for during a busy maintenance job.
Interviewer tipListen for their own method of tracking tool issues and returns, a final check, and the result. Claiming all turbine service tools were returned without checking is a red flag; ask what they would improve.
Candidate tipChoose a maintenance job where several technicians shared tools. Show how you tracked who had each tool, checked returns, and left an accurate tool inventory at the end.