Service Technician Interview Questions
For mechanics who install and repair commercial and industrial refrigeration systems. Interviews focus on reading system drawings, charging systems and recovering refrigerant.
30 questions, ranked by what the job needs most
In other fields: Bus and Truck Mechanics and Diesel Engine Specialists · Automotive Master Mechanics · Electrical and Electronics Repairers, Commercial and Industrial Equipment · all 23 sets →
Print the top 10:Scoring sheetPractice sheet
Question 1: Walk me through charging a refrigeration system to its specifications, including any valve settings its procedure requires.
Example answerThe interviewer wants to learn whether you use the system's specifications to set valves and establish the correct refrigerant charge. Walk through one system type you know. Separate the charging method from any valve settings the service procedure requires, and finish with the operating checks.
For example: "I identify the refrigerant and get the charging instructions for that system. On a system specified for charging by weight, I first confirm that repairs, leak testing and evacuation are complete. I weigh in the specified amount, including any adjustment the instructions require for the installed piping. I set or position valves only as that procedure directs. Once the system stabilizes, I compare its pressures and temperatures with the specified operating checks and record the refrigerant amount and readings."
Describe the method that actually applies to your system. Avoid treating superheat or subcooling as a universal charging method, turning valves to hide an incorrect charge, or adding refrigerant without investigating why the charge is low.
Interviewer tipExpect the specified refrigerant, charging method and final operating checks. Valve settings must follow that system's procedure; using valve adjustments to disguise a wrong charge is a red flag.
Candidate tipName the system and refrigerant. Follow its specified charging method, explain any required valve settings separately, and describe the readings that confirm the charge.
Question 2: How do you choose a safe test pressure when checking refrigeration piping for leaks?
Interviewer tipA competent answer uses the equipment instructions and the lowest applicable component pressure limit, with suitable test gas and pressure controls. Using oxygen or exceeding a component's rating is unsafe.
Candidate tipExplain where you find the pressure limits and how the components in the test section affect your choice. Include the test gas, regulator and safeguards against overpressure.
Question 3: How do you keep the inside of refrigeration tubing clean while brazing a repair joint?
Interviewer tipExpect preparation that keeps debris out and a controlled dry nitrogen purge as the equipment instructions require. Brazing with refrigerant still present or pressurizing a closed tube while heating is unsafe.
Candidate tipWalk through preparing the tubing and arranging the purge. Explain how you keep oxidation and debris out without building pressure inside the tubing.
Question 4: How do you safely test a refrigeration control circuit for continuity?
Interviewer tipExpect isolation of power, verification that the circuit is de-energized and checks against the wiring diagram. Using a continuity setting on an energized circuit is unsafe.
Candidate tipWalk through preparing the circuit, choosing test points from the diagram and interpreting the reading. Explain how you avoid readings through other connected components.
Question 5: Describe a time you repaired damaged refrigeration wiring that would have failed again if you had only replaced the wire.
Interviewer tipA useful example identifies what damaged the wire, the repair they made and how they checked it. Replacing a burned wire without addressing the cause leaves the fault unresolved.
Candidate tipPick a wiring repair involving heat, rubbing, moisture or another cause. Focus on how you found the damage source, corrected it and verified the repair.
Question 6: Describe a time you brazed or soldered a leaking joint in a commercial refrigeration system.
Interviewer tipListen for how they prepared the tubing, why the filler metal suited the joint, and how they confirmed the leak was fixed. Putting the system back into service without checking the repaired joint for leaks is a red flag.
Candidate tipPick one joint you repaired. Explain how you prepared the tubing, what filler metal you used to seal the joint, and how you checked for leaks after the repair.
Question 7: Share an example of how a customer's description helped you narrow down an intermittent refrigeration problem.
Interviewer tipListen for the questions they asked about timing, use and symptoms, plus what that ruled out. Dismissing the customer's observations or claiming a diagnosis without testing is a concern.
Candidate tipChoose one intermittent fault. Describe what the customer noticed, the questions you asked and how their answers narrowed your checks. End with the confirmed cause.
Question 8: Describe a time you repaired a compressor, fan motor or other mechanical part on a refrigeration system.
Example answerThe interviewer wants to know whether you diagnose before replacing parts and whether you look for what caused the failure. Use Situation, Task, Action, Result. Sample answer: "A reach-in cooler at a convenience store was warm, and the condenser fan wasn't running. I had voltage at the motor, so I tested the capacitor and the motor windings. The capacitor was within range, but one winding was open, so the motor had failed. The condenser coil was packed with dust and grease, which likely made the motor run hot for a long time. I replaced the motor with one of matching rating, cleaned the coil, and checked amp draw against the nameplate. I watched the head pressure come down and the box pull back to temperature, then suggested the store add coil cleaning to its maintenance plan." Pitfalls to avoid: describing a part swap with no testing; skipping the root cause; ending before you show the system held temperature.
Interviewer tipListen for how they confirmed the part had failed and looked for the root cause, such as a bad contactor or low charge. Swapping parts until it works is a red flag.
Candidate tipExplain the symptom, the tests that pointed to the part, the repair, and how you confirmed the system held temperature afterward.
Question 9: What's the hardest part of using gauges and other instruments to tell whether a commercial refrigeration system is running properly?
Interviewer tipA strong answer connects pressure and temperature readings to the conditions at the time of the test. Treating a single pressure reading as proof the system is working is a red flag.
Candidate tipPick one testing challenge, such as readings that shift as cooling demand changes. Explain how you compare pressure and temperature readings with what you'd expect under those conditions.
Question 10: Tell me about a time a close inspection of a refrigeration system helped you find the cause of a problem.
Example answerThe interviewer wants to see that you look carefully before you fix, and that you can connect what you see to the cause. Use Situation, Task, Action, Result. Sample answer: "A walk-in cooler kept icing up, and the restaurant had already had the coil defrosted twice. Instead of defrosting it again, I went over the whole box. The door gasket was torn near the bottom hinge and the door wasn't closing fully, so warm, humid air was getting in. I checked the frost pattern and inspected the gasket along the full door edge before settling on the air leak as a cause. I replaced the damaged gasket and adjusted the door closer so the door sealed. I came back the next week to check, and the coil was clear. I explained to the manager how the open door caused the icing so the staff would watch for it." Pitfalls to avoid: describing only the repair; skipping what made you look past the obvious; claiming a result you didn't check.
Interviewer tipListen for what they checked, such as coils, fittings, oil spots, frost patterns or door gaskets, and how that led to the cause. Jumping to a fix without looking is a red flag.
Candidate tipDescribe the complaint, what you inspected and in what order, the clue that gave the problem away, and how you confirmed the cause before repairing it.
Question 11: Tell me about a time you combined what a customer told you, your readings and the service manual to find a fault.
Interviewer tipA strong answer shows they ask good questions, test rather than trust one source, and sort useful facts from noise. Dismissing what the customer said is a red flag.
Candidate tipExplain what the customer reported, what your gauges or meter showed, what the manual or wiring diagram said, and how those pieces pointed you to the cause.
Question 12: What would you do if you noticed refrigerant escaping into an enclosed equipment room while preparing to service a system?
Interviewer tipPeople's safety comes before finding the leak: leave the hazardous area and follow the site's emergency response process. Entering or staying in the room without assessing the hazard is unsafe.
Candidate tipStart with protecting yourself and others. Explain how you would raise the alarm and get trained emergency help before anyone attempts service or re-entry.
Question 13: Walk me through a preventive maintenance visit on a commercial refrigeration system, including how you decide what it needs.
Interviewer tipListen for a routine covering coils, drains, fans, electrical connections and readings, plus the unit's history. Not checking past service records or the manufacturer's schedule is a red flag.
Candidate tipDescribe a real visit. Cover the checks you always do, how readings and past records told you what else to look at, and how you reported what you found to the customer.
Question 14: Tell me about a time you found a mismatch between a refrigeration control wiring diagram and the wires at the unit.
Interviewer tipThe example should show how they identified wires and resolved the mismatch before making connections. Guessing from wire color alone is a red flag; ask how they verified the finished circuit.
Candidate tipSet out what did not match the diagram. Explain your checks, how you confirmed the intended connections and the result when you tested the controls.
Question 15: Walk me through a time you corrected a defrost timer setup that was causing trouble in a freezer.
Interviewer tipA strong case connects timer settings to the freezer's actual operation and includes a checked result. Changing settings without checking the equipment instructions is a concern.
Candidate tipDescribe the freezer symptoms and the timer setup you found. Spend most of the answer on your checks and adjustments, then explain how you confirmed defrost worked afterward.
Question 16: Recall a situation where you corrected refrigeration control settings that were making the system cycle poorly.
Interviewer tipThe answer should distinguish a setting problem from a failed component and show checks against the manufacturer's recommendations. Defeating protective controls to stop cycling is unsafe.
Candidate tipDescribe the cycling pattern, the settings you checked and the evidence behind your adjustments. End with how the system ran afterward and what you learned.
Question 17: Describe your role in a refrigeration system overhaul where the used refrigerant was sent for reclamation.
Example answerThe interviewer wants to understand your overhaul experience and your role in handling refrigerant that goes to a reclaimer.
Use Situation, Task, Action, Result. Describe the equipment problem, your mechanical work, how refrigerant was recovered and sent for reclamation, and the checks before return to service. Separate your work from the reclaimer's processing and purity verification.
For example: "A compressor needed an overhaul. After making the equipment safe for the work, I recovered the used refrigerant into a suitable labeled cylinder and arranged shipment to a reclaimer. I completed the mechanical repairs, leak tested and evacuated the system, then charged it with new refrigerant of the type specified for the equipment. I checked operation before returning it to service. The recovered refrigerant went through the reclaimer's process separately."
Describe only work you actually performed. Avoid calling refrigerant reclaimed just because it was collected, claiming you performed the reclaimer's work, or leaving out the checks that established the overhaul was successful.
Interviewer tipListen for their overhaul work, refrigerant recovery and the reclaimer's separate role in meeting a purity standard. Calling collected refrigerant reclaimed without verification is a red flag.
Candidate tipUse a real overhaul. Describe your mechanical work, recovery into a suitable cylinder, the handoff to a reclaimer and the checks before return to service. Separate your work from the reclaimer's.
Question 18: How should recovered refrigerant be handled when you suspect it is mixed with another refrigerant?
Interviewer tipExpect identification, separate compatible recovery storage and routing through the proper reclamation or disposal process. Returning an unknown mixture to a system or venting it is unacceptable.
Candidate tipExplain how you would keep suspect refrigerant separate, identify the cylinder contents and arrange the next step. Distinguish recovery from reclaiming refrigerant to a purity standard.
Question 19: Tell me about a time you spotted a problem in a system's pressures, temperatures or service records before it caused a breakdown.
Example answerThe interviewer wants to know whether you pay attention to small changes and act before a customer loses product. Use Situation, Task, Action, Result. Sample answer: "During a routine visit to a supermarket, I compared the rack's readings with the service log from earlier visits. Suction pressure on one circuit was a little lower each time, and a case on that circuit was running a few degrees warmer than before, though still within range. I checked the sight glass and superheat, which pointed to a slow loss of refrigerant. I did a leak search on that circuit and found a leaking flare fitting at one case. I repaired it, recharged the circuit, recorded the refrigerant added, and noted it all on the work order. The manager was glad we found it before the case lost temperature over a weekend." Pitfalls to avoid: saying everything was in range so you moved on; skipping how you confirmed the cause; claiming numbers or savings you can't back up.
Interviewer tipA strong answer shows they compare readings to normal and to past visits and act on a trend. Ignoring a small drift because the box still holds temperature is a red flag.
Candidate tipExplain what reading or record caught your eye, why it was not normal, what you did about it, and what would likely have happened if you had not.
Question 20: Walk me through how you read blueprints and specifications to plan a refrigeration installation.
Example answerThe interviewer wants to know whether you can turn drawings into a working plan and catch problems before they become costly on site. Explain your process in the order you use it. Sample answer: "I start with the equipment schedule to confirm the model, capacity and refrigerant for each unit, then find each piece on the floor plan. I check the routing for refrigerant lines and compare line sizes and lengths with the manufacturer's installation guide, because long runs can change line sizing and oil return. I look at the electrical drawings for voltage and disconnect locations, and at the details for drains, supports and clearances. On one walk-in cooler job, the plan showed the condensing unit where a rooftop exhaust fan already sat, so I raised it with the foreman before we ordered materials, and the engineer moved it." Pitfalls to avoid: saying you mostly figure it out on site; ignoring the manufacturer's installation guide; not saying how you handle drawings that don't match the site.
Interviewer tipListen for how they find equipment locations, line sizes, capacities and electrical needs and check them against the manufacturer's requirements. Not asking about unclear drawings is a red flag.
Candidate tipDescribe a real install. Explain what you looked for on the drawings, how you checked capacity and line sizes against the specs, and what you did when something did not match the site.
Question 21: Describe a time you found that a newly installed refrigeration system did not meet its specified performance during testing.
Interviewer tipLook for measured performance compared with the installation specifications and a retest after correction. Signing off solely because the compressor runs is a red flag.
Candidate tipChoose an installation test with a clear shortfall. Explain the required performance, your test conditions, what you corrected and the final verification.
Question 22: Tell me how you handled a difficult refrigeration installation.
Interviewer tipListen for a specific installation obstacle, their safe response and the final system checks. An answer that never explains their own work or the result is a red flag.
Candidate tipPick one install. Explain the challenge, the options you weighed, what you did, and how you tested the system before handing it over.
Question 23: Describe a time you resolved a conflict between a refrigeration installation drawing and the manufacturer's required service clearance.
Interviewer tipListen for their own comparison of the drawing and required clearance, coordination to resolve the conflict, and the result. Installing against the required clearance and leaving it for the service crew is a red flag.
Candidate tipUse one installation. Explain how you checked the drawing against the model's instructions, got the layout corrected or confirmed, and what happened before equipment was placed.
Question 24: How do you protect a new refrigeration expansion valve from damage during installation?
Interviewer tipExpect confirmation of the valve specification, protection from brazing heat and contamination, and correct placement of sensing parts where fitted. Heating the valve without protection risks damage.
Candidate tipWalk through checking the replacement valve, preparing the connections and protecting sensitive parts. Include the manufacturer's mounting instructions and checks before startup.
Question 25: Tell me about a time you found contamination before connecting refrigerant lines to refrigeration equipment.
Interviewer tipThe example should show how they kept contamination out of the equipment and checked the lines before connection. Connecting known dirty or wet lines and relying on the system to clear them is a red flag.
Candidate tipUse one installation or repair. Describe what you found in the lines, how you dealt with it and how you established that the connection could be completed cleanly.
Question 26: Tell me about the last time you mounted compressor, condenser, and other components in specified locations on frames, using hand tools and acetylene welding equipment.
Question 27: What do you check before tightening a refrigeration compressor onto its mounting frame?
Interviewer tipExpect the specified location, level and alignment, mounting hardware and any required vibration isolators. Forcing pipe connections to pull a misaligned compressor into place is poor practice.
Candidate tipWork from the frame and mounting instructions to the compressor's position and connections. Explain which checks prevent strain or vibration before you secure the hardware.
Question 28: What kind of experience do you have cutting, bending, threading, and connecting pipe to functional components and water, power, or refrigeration system?
Question 29: How do you prepare and bend refrigeration tubing without restricting the bore or leaving debris inside?
Interviewer tipExpect a suitable bender and bend radius, control of kinks or flattening, and clean cutting and deburring. Installing visibly kinked tubing is a red flag.
Candidate tipGo from measuring and cutting to bending and checking the finished tube. Explain how you keep chips out and recognize a bend that must be remade.
Question 30: Walk me through a time you caught a measurement error while marking locations for refrigeration equipment.
Interviewer tipThe example should identify the reference point, how they caught the error and the correction before installation. Passing on measurements known to be wrong is a concern.
Candidate tipDescribe the layout and the measurement that did not fit. Explain how you checked the reference points, corrected the marks and confirmed the equipment would fit.
New to interviews? Start with the common questions every interview asks →