Skip to content

Test Technician Interview Questions

For technicians who work on automated and electromechanical equipment. Interviews focus on testing assemblies, calibrating instruments and finding faults.

30 questions, ranked by what the job needs most

Also for Test Technician: Office Clerks, General · Inspectors, Testers, Sorters, Samplers, and Weighers · Geological Sample Test Technicians · all 9 sets →

Print the top 10:Scoring sheetPractice sheet

  1. Question 1: Walk me through how you test the performance of an electromechanical assembly using instruments such as an oscilloscope, multimeter or bridge.

  2. Question 2: Walk me through how you traced and fixed a fault that made a motor-driven assembly stop mid-cycle.

  3. Question 3: Walk me through how you read a blueprint, schematic or wiring diagram to work out the steps and order for building an assembly.

  4. Question 4: Share an example of a time you installed or updated control software on a microprocessor-based machine.

  5. Question 5: Describe a time you repaired or calibrated an electronic control, sensor or drive on a piece of automated equipment.

  6. Question 6: What would you do if you were asked to bypass a machine's safety interlock to keep it running while waiting for a repair?

  7. Question 7: Tell me about a time you installed electrical or electronic parts in a housing or assembly using soldering equipment and hand tools.

  8. Question 8: Tell me about a time your attention to detail, such as rechecking a wiring connection or a measurement against the drawing, caught a mistake.

  9. Question 9: Describe a test you performed on an electromechanical assembly that led to an improvement in its quality or performance.

  10. Question 10: Tell me about a time a close inspection of a part or assembly, such as spotting a surface defect or worn connector, helped you find a problem.

  11. Question 11: How do you decide whether a scratch or other surface defect makes an electromechanical part unacceptable?

  12. Question 12: Share an effective method you have used to ensure that part dimensions/clearances conform to specifications.

  13. Question 13: Tell me about your experience aligning, fitting, and assembling component parts.

  14. Question 14: Describe a time you improved the build steps for a repeated electromechanical assembly.

  15. Question 15: Describe a time when you successfully serviced, repaired, or tested a machine or device that operates mainly by mechanical principles.

  16. Question 16: Tell me about the last time you performed routine maintenance on equipment. How did you determine when and what type of work was needed?

  17. Question 17: What would you check before using a substitute motor in an electromechanical assembly when the specified motor is unavailable?

  18. Question 18: Walk me through a time you revised a CAD drawing to make an electromechanical design change clear to the people building it.

  19. Question 19: Give an example of how you improved a parts inventory system for electromechanical equipment.

  20. Question 20: Share an experience in which you successfully repaired, reworked, and/or calibrated hydraulic or pneumatic assemblies or systems.

  21. Question 21: Describe a new robot which you successfully developed or programmed.

  22. Question 22: Tell me about a time when you successfully trained others in the use or maintenance of robots. What methods made you successful?

  23. Question 23: Provide an experience in which you successfully operated metalworking machines to fabricate housings, jigs, fittings, or fixtures.

  24. Question 24: Share an experience in which you successfully operated, tested, and/or maintained robotic equipment used for green production applications. What methods made you successful?

  25. Question 25: Tell me about your last experience doing repair work. How did you determine what tools you needed?

  26. Question 26: Tell me about a time you had to learn a new machine, controller or piece of test equipment quickly.

  27. Question 27: Share an experience in which you successfully installed a difficult piece of equipment. What made the situation so difficult?

  28. Question 28: Describe an experience in which you successfully controlled the operation of a difficult system. What made you successful?

  29. Question 29: Name a time when you identified strengths and weaknesses of alternative solutions to problems. What was the impact?

  30. Question 30: Provide an example when your ethics were tested.