Trouble Shooter I Interview Questions
For electricians doing general installation and repair work. Interviews focus on testing electrical equipment, replacing wiring and fixtures, and meeting electrical codes.
30 questions, ranked by what the job needs most
Print the top 10:Scoring sheetPractice sheet
Question 1: How have you used electrical drawings to choose a code-compliant spot for a panel?
Interviewer tipListen for how they checked access and room to work at the panel on site. Treating a spot on the drawing as proof of code compliance is a red flag.
Candidate tipPick a panel location you checked against the drawings and the conditions on site. Explain how the code rules for access and room to work affected where you put the panel.
Question 2: Share an example of a time you dealt with a difficult wire pull through conduit.
Interviewer tipA strong example shows how they found the cause of resistance and finished the pull without damaging insulation. Forcing the wire despite signs of damage is a red flag; ask what they would change next time.
Candidate tipChoose one difficult conduit run. Focus on how you checked the route, adjusted the pull, and confirmed the wires were undamaged; finish with the result.
Question 3: What do you weigh when planning a conduit run through a ceiling shared with other trades?
Interviewer tipA strong answer accounts for ducts and pipes, room for bends and access to pull wire. Planning a route through space reserved for a duct without resolving the clash is a red flag.
Candidate tipConduit is tubing that protects wiring. Explain how you plan its route around ducts and pipes while leaving room for bends and access to pull the wire.
Question 4: Walk me through a job where you wired and installed a row of outlets on a new circuit.
Interviewer tipListen for the candidate's own work securing the outlets and connecting the wires, followed by a check of the finished installation. Leaving a loose connection in service is a red flag.
Candidate tipPick one run of outlets and describe how you mounted and wired them. End with the check that showed the outlets were ready to use.
Question 5: What do you check before connecting a conductor to a circuit breaker terminal?
Interviewer tipExpect isolation and verification that power is off, matching conductor size and material to the terminal rating, and the specified tightening torque. Fitting an unapproved conductor into the terminal is wrong.
Candidate tipWalk through making the circuit safe, checking the breaker's terminal markings and instructions, and preparing and tightening the conductor as specified.
Question 6: Describe a time you used electrical test instruments to decide whether a circuit was ready to power new equipment.
Interviewer tipA strong answer ties meter readings to the equipment's ratings and names a safety check, such as verifying grounding. Treating a successful startup as proof the circuit is safe is a red flag.
Candidate tipChoose a circuit you tested for new equipment. Name the tester, the readings you compared with the equipment's ratings and the safety check that helped you decide whether it was ready.
Question 7: Describe how you resolved a case where a breaker kept tripping as soon as a piece of equipment started.
Interviewer tipListen for evidence that links the startup trip to a specific cause and for a check after the fix. Repeatedly resetting the breaker and leaving the cause unresolved is a red flag.
Candidate tipName the equipment and the clue that narrowed down the cause of the trip. Explain what you corrected and what you observed when the equipment started again.
Question 8: Tell me how you tracked down and fixed a lighting problem that kept coming and going.
Interviewer tipListen for the clue that helped them trace the fault and a check under the conditions that brought it on. Assuming it was fixed because the lights came back on once is a red flag.
Candidate tipPick a case where the lights worked normally between failures. Explain what pattern helped you narrow down the cause, what you fixed and how you checked the fix held.
Question 9: Walk me through a recent repair where you replaced damaged wiring, a device or a fixture, from finding the problem to closing it up.
Example answerThe interviewer wants to hear your full repair routine: making it safe, finding the cause, choosing the right parts and testing before you leave.
Walk through the job in order. Cover isolating the circuit, preventing re-energization and verifying absence of voltage, what damage you found and why it happened, how you matched the replacement to the circuit, and how you tested and cleaned up.
Sample answer: "A store manager called about a light fixture that flickered and smelled hot. I isolated the circuit and applied my lock and tag to prevent re-energization. I checked for absence of voltage with a suitable meter, proving it on a known live source before and after the check. Inside the fixture the wire insulation was brittle from heat, because someone had installed lamps hotter than the fixture was rated for. The brittle insulation ran too far back to trim, so I replaced the fixture whip and installed a new fixture rated for the lamps they wanted. I checked the connections, restored power, tested it, and told the manager what wattage to use going forward."
Pitfalls to avoid: leaving out how you made sure the circuit was dead, fixing the symptom without finding the cause, and forgetting to mention testing the repair.
Interviewer tipA strong answer covers shutting off and verifying the circuit is dead, finding the root cause, and matching the replacement to the circuit. Skipping lockout or testing first is a red flag.
Candidate tipPick one real repair. Explain how you made it safe, what you found, why you chose the parts you used, and how you tested it before handing it back.
Question 10: Describe a time you changed your ladder or scaffold setup to work safely on electrical wiring or fixtures.
Interviewer tipListen for the access problem, their own changes to the ladder or scaffold, and the result. Reaching farther instead of correcting an unstable setup is a red flag; ask what they learned.
Candidate tipUse a real electrical job above floor level. Briefly describe the access problem, then explain your changes to the ladder or scaffold and how they made the work safer.
Question 11: Describe a time an inspection of an electrical system or piece of equipment helped you find a hazard or defect before it caused a problem.
Example answerThe interviewer wants to know that you look closely, recognize warning signs and act on them before someone gets hurt or equipment fails.
Use Situation, Task, Action, Result. Say what you were inspecting and why, what you noticed, how you confirmed it was a real problem, and what you did, including who you told.
Sample answer: "During a scheduled inspection shutdown at a small manufacturing plant, I isolated and locked out a conveyor circuit and verified absence of voltage. Inside its disconnect, I noticed a discolored lug. I found the lug was loose and the conductor had started to overheat. I told the maintenance supervisor that running it that way could cause a failure or a fire. We kept the conveyor isolated and locked out while I cut back the damaged conductor, replaced the lug and torqued it to the manufacturer's spec. After checking the repair, I followed our restart procedure and confirmed normal operation. I also suggested adding that panel to their regular inspection list."
Pitfalls to avoid: being vague about what you actually saw, leaving out how you made the work safe, and not saying who you reported the hazard to.
Interviewer tipA strong answer names what they checked, the warning sign they spotted, such as heat damage, loose terminations or a missing ground, and how they reported and fixed it. Vague answers are a red flag.
Candidate tipSay what you were inspecting and why, what caught your eye, how you confirmed the problem, and what you did about it, including who you told.
Question 12: Tell me about a time your attention to detail on an install, such as terminations, labeling or box fill, kept a job from failing inspection or creating a hazard.
Example answerThe interviewer wants proof that you check the small things that decide whether work is safe and passes inspection.
Use Situation, Task, Action, Result. Pick one specific detail, explain why it mattered, and describe the habit that helped you catch it.
Sample answer: "On a tenant fit-out, I was finishing devices before the final inspection. I make a habit of checking box fill on any box with several cables, and one box behind a counter had more conductors than its size allowed because a circuit had been added late. I swapped in a deeper box with an extension ring, re-made the splices and checked the panel schedule against what was actually installed. Two circuits were labeled wrong, so I fixed those too. The inspection passed without corrections, and the foreman started adding a box fill check to our pre-inspection walk."
Pitfalls to avoid: saying you are detail-oriented without a real example, picking a detail that had no effect on safety or quality, and leaving out the check you do every time, not just once.
Interviewer tipLook for checks they do out of habit, such as torquing to spec, labeling circuits and checking box fill, and a catch that mattered. Claiming to be detail-oriented with no example is a red flag.
Candidate tipPick a real detail you caught, explain why it mattered for safety or inspection, and describe the habit or check that helped you catch it.
Question 13: How do you check that electrical equipment is suitable for a damp or wet location during an inspection?
Interviewer tipListen for checking the actual exposure, equipment markings or listing, and installation instructions against the applicable code. Assuming a cover makes any equipment suitable for a wet location is wrong.
Candidate tipStart with the moisture exposure at the installation. Explain how you compare it with the equipment's location rating, markings, and installation instructions.
Question 14: Walk me through a job where you connected power cables and a ground wire to a piece of electrical equipment.
Interviewer tipListen for how they confirmed the power cables were on the right terminals and the ground connection was sound. Turning the power on before checking the ground is a red flag.
Candidate tipName the equipment and the connections you made yourself. Describe your checks at the power and ground terminals and explain what those checks showed before the equipment was turned on.
Question 15: Tell me about a time you had to change how you secured a switch or outlet box because the wall would not hold it firmly.
Interviewer tipLook for the wall condition, their choice of box support, and a firm installation. Concealing a loose box is a red flag; ask what they learned about choosing supports.
Candidate tipPick one loose or hard-to-secure box. Describe the wall condition, the support you chose, and how you checked that the finished box stayed firm.
Question 16: What would you do if a manager wanted to keep running equipment after you found signs of overheating at its electrical connections?
Interviewer tipExpect a clear warning about continued operation and a request for a safe shutdown before repair. Agreeing to keep the equipment running without addressing the overheating hazard is a red flag.
Candidate tipPut the overheating hazard first. Explain how you would describe the risk to the manager and recommend taking the equipment out of service safely for inspection and repair.
Question 17: In your experience, what is the key to ensuring your company was compliant with all laws, regulations and standards that were applicable to your area of responsibility?
Example answerThe interviewer wants to know how you make sure your work follows the rules that apply to it, and what you do when you find a gap.
Name the approach you rely on, then support it with an example. Strong answers cover knowing which rules apply, building checks into the routine, keeping records, and staying current when rules change. Rules vary by industry and state, so speak to the ones you have actually worked with.
Sample answer: "I think the key is making compliance part of the routine rather than a yearly scramble. In my last role, I kept a checklist of the requirements that applied to our records, did a short self-check each month, and kept notes on any fixes. When a new record-keeping rule came out, I read the guidance, updated the checklist, and briefed the team. Our next audit found no issues in our area."
Pitfalls: Don't claim you know every law. Avoid suggesting compliance is someone else's job. Don't offer legal interpretations; describe your process.
Question 18: Tell me about the various tools and equipment you have used.
Question 19: Tell me about a time you had to learn a code change or a newer technology, such as EV chargers or smart controls, and put it to use on a job.
Example answerThe interviewer wants to know that you keep learning as codes and equipment change, and that you apply what you learn correctly.
Use Situation, Task, Action, Result. Name what was new, how you learned it, how you used it on a job and how you checked your work. Code adoption varies by state and city, so speak about the rules where you worked.
Sample answer: "Our area adopted a newer code edition with expanded GFCI and AFCI requirements, and around the same time we started getting requests for home EV chargers. I took a continuing education class on the code changes and read the installation manual for the charger the customer bought. On the first install, I did a load calculation to confirm the service could handle it, sized the circuit to the charger's instructions and pulled the permit. The install passed inspection, and I wrote up a short checklist the rest of the crew now uses."
Pitfalls to avoid: saying you learn on the job without naming how, skipping how you made sure the work met code, and claiming training or certifications you do not have.
Interviewer tipListen for how they keep up with code cycles and new equipment, such as manufacturer training or continuing education, and how they applied it correctly. Relying only on old habits is a red flag.
Candidate tipName the change or technology, how you learned it, and the job where you used it. Mention what you did differently and how you made sure it met code.
Question 20: Walk me through how you plan and prioritize your work on a job site when several tasks, inspections and other trades all compete for your time.
Example answerThe interviewer wants to see that you can keep a job moving: knowing what must happen first, working around other trades and inspections, and adjusting when plans change.
Describe your planning routine, then back it up with a real example. Cover how you sort tasks, how you coordinate with the foreman or general contractor, and how you handle delays.
Sample answer: "At the start of each week I look at the schedule with my foreman and list what has to be done before each inspection. Rough-in on walls that drywall is waiting for comes first, because other trades are held up by it. On one office job, the material for a panel was delayed. Instead of waiting, I moved my helper to pulling wire in another area and called the supplier daily. I told the general contractor right away so they could adjust drywall. We still made the rough-in inspection on time."
Pitfalls to avoid: describing a to-do list with no sense of what comes first, ignoring other trades and inspections, and leaving out how you communicate schedule changes.
Interviewer tipListen for how they sequence rough-in around inspections and other trades and how they adjust when the schedule slips. No plan beyond working hard is a red flag.
Candidate tipUse a real job. Say how you plan the day or week, how you order tasks around inspections, deliveries and other trades, and how you adjust when something changes.
Question 21: Tell me about a time you had to tell a customer or contractor that their wiring or panel was unsafe or would not pass inspection.
Example answerThe interviewer wants to know that you will speak up about safety, explain it clearly and stay respectful, even when the news is costly or unwelcome.
Use Situation, Task, Action, Result. Say what you found, how you explained it in plain language, what options you offered and what happened.
Sample answer: "A homeowner hired me to add a circuit for a new appliance. After safely isolating the panel and verifying absence of voltage, I found two conductors on breaker terminals rated for only one, plus a scorched bus connection. I knew the customer wanted a quick, cheap job, so I showed them the damage with a flashlight and explained that it could overheat and start a fire. I kept the panel out of service while checking repair options. The manufacturer allowed replacement of that bus assembly with a specified part. I explained that repair and a panel replacement, with rough costs for each. They chose the permitted repair. I corrected the breaker terminations and tested the repaired panel before adding the circuit. Later they thanked me for showing them instead of just telling them."
Pitfalls to avoid: using scare tactics or pushing extra work, using jargon the customer cannot follow, and agreeing to leave an unsafe condition as it is.
Interviewer tipLook for a clear, calm explanation of the hazard and the options, without scare tactics or upselling. Giving in and leaving an unsafe condition in place is a red flag.
Candidate tipDescribe what you found and why it mattered, how you explained it in plain words, what options you gave, and how the customer or contractor responded.
Question 22: Share an experience in which you trained workers in electrical work. What methods made you successful?
Question 23: How do you keep track of electrician license or identification card requirements where you work?
Interviewer tipA sound approach checks state and local licensing authorities, tracks expiration dates, and completes any required renewals or education. Assuming one license covers every location is a red flag.
Candidate tipExplain where you verify the rules for each place you work and how you track renewal dates and any required education. Avoid treating one state's requirements as universal.
Question 24: How do you check a hand-fabricated mounting bracket against its specifications before using it to support electrical equipment?
Interviewer tipThe answer should compare material, dimensions, hole placement, and fit with the specifications. Using a bracket with cracks or sharp edges against wiring is a red flag.
Candidate tipWalk through comparing the finished bracket with the drawing or job specifications, including its material, dimensions, mounting holes, and edges. Explain how you resolve any mismatch before installation.
Question 25: Describe an experience in which you provided preliminary sketches and/or cost estimates for materials and/or services.
Question 26: Provide an experience in which you effectively performed business management duties.
Question 27: Provide an experience in which you effectively performed physically demanding tasks.
Question 28: Describe how you handled a conflict with a general contractor, another trade or a customer on an electrical job.
Example answerThe interviewer wants to learn how you handle disagreements on an electrical job while keeping the working relationship productive.
Use Situation, Task, Action, Result to organize one real example. Briefly describe the disagreement and your responsibility. Spend most of the answer on what you said and did to understand the other person's concern and address the conflict. End with the result for the job and something you learned.
For example: "A general contractor was upset that our unfinished conduit work was delaying the ceiling crew. I needed access above the ceiling to finish the run. I walked the area with the contractor, listened to the schedule concern and pointed out where we still needed access. We agreed on which areas the ceiling crew could start while we finished the remaining section. Both crews could keep working. I learned to flag access needs earlier so the contractor could plan around them."
Avoid blaming the other person, describing only what the crew did without explaining your part, or claiming the conflict was resolved without saying what changed.
Interviewer tipListen for the electrician's own actions, the result for the job and a lesson learned. Insulting the contractor, other trade or customer instead of addressing the disagreement is a red flag.
Candidate tipChoose one real conflict on an electrical job. Briefly explain the disagreement, focus on what you did with the contractor, other trade or customer, and finish with the result and what you learned.
Question 29: How do you balance cooperation with others and independent thinking? Share an example.
Example answerThe interviewer wants to see that you can work well with a team while still bringing your own judgment, and that you know when to speak up and when to go along.
Start with a short answer about how you balance the two, then give one example. A good example shows you sharing your own view, listening to others, and then supporting the team's decision even if it wasn't yours.
Sample answer: "I try to form my own view first, share it clearly, and then commit to whatever the group decides. On one project, the team wanted to launch a new form right away. I thought we should test it with a few users first and explained why. We agreed on a one-week trial. Testing found a confusing field, we fixed it, and the full launch went smoothly."
Pitfalls: Don't present yourself as someone who always goes along or always insists on your own way. Avoid a story where you ignored the team's decision. Don't skip the example.
Interviewer tipTry to determine if the candidate has a cooperative attitude or is otherwise good-natured.
Candidate tipThe employer wants to know that you have a cooperative attitude or are otherwise good-natured.
Question 30: Provide an example when your ethics were tested.
Example answerThe interviewer wants to know whether you do the right thing when it is inconvenient, and how you handle pressure to cut corners.
Use Situation, Task, Action, Result. Describe the pressure or temptation without naming people, explain the choice you made and why, and how you handled the conversation. Keep the focus on your actions, not on judging others.
Sample answer: "Near the end of a quarter, a coworker asked me to record a sale as complete even though the customer hadn't signed yet, so our numbers would look better. I told them I wasn't comfortable doing that and suggested we tell our manager the deal would close the following week. My manager agreed it should wait. The customer signed early in the new quarter, and our records stayed accurate."
Pitfalls: Don't say your ethics have never been tested. Avoid stories that make you sound self-righteous or that share confidential details. Don't pick an example where you went along with the wrong choice and stop there.