Aircraft Refueler Interview Questions
For drivers hauling freight in heavy trucks or tractor-trailers. Interviews focus on maneuvering into loading areas, adjusting routes and checking truck safety equipment.
30 questions, ranked by what the job needs most
Print the top 10:Scoring sheetPractice sheet
Question 1: Walk me through your pre-trip inspection on a tractor-trailer, from the engine compartment back to the trailer.
Example answerThe interviewer wants to know whether you inspect your truck thoroughly every time.
Describe your usual inspection order. Show that you know the key systems and what you do when something fails.
Sample answer: "I start by checking under the truck for leaks, then open the hood and check fluid levels, belts, hoses and the steering parts. In the cab I check my gauges, mirrors, horn, wipers and emergency equipment, like the fire extinguisher and warning triangles. I follow the brake test procedure for that truck, securing it for each test. I check how the air pressure builds, listen and check for leaks, test the low-air warning and emergency brake application, then test that the parking brake holds and the service brakes stop the truck. Outside I walk around for tires, wheels, lights and reflectors, then check the coupling, that the fifth wheel is locked on the kingpin, and the air and electrical lines. I finish with the trailer, its doors and its tires. If I find a defect, I write it up and call the shop before I roll."
Pitfalls to avoid: describing a quick walk-around only, skipping the air brake check, and driving with an unresolved safety defect to make a delivery time.
Interviewer tipA strong answer follows a set order and names brakes, air lines, tires, lights, coupling and emergency equipment; a candidate who can't describe the air brake check is a red flag.
Candidate tipDescribe your order step by step, including the air brake test, coupling, tires and lights, and the emergency gear you check. Say what you do when you find a defect.
Question 2: How do you track your hours of service so you stay within federal limits on a long run?
Example answerThe interviewer wants to know that you understand hours-of-service rules and plan your day so you stay legal without being pushed into unsafe driving.
Explain how you plan before the trip, how you use your logging device during it, and what you do when something throws off the plan.
Sample answer: "Before I leave, I look at the distance, the appointment times and where I can park, and I plan my breaks and my rest stop around my available hours. I keep my status on the electronic logging device current all day, so on-duty time at the dock is logged too. If a shipper keeps me waiting, I check my remaining hours and tell dispatch early if I won't make the delivery, instead of trying to make up time on the road. When I'm getting close to my limit, I find safe parking before I need it, not after."
Pitfalls to avoid: quoting rules you're unsure of, falsifying logs to finish a load, and ignoring time spent waiting at docks.
Interviewer tipStrong answers show trip planning for breaks and rest, accurate duty records and a response to delays. Driving beyond available hours or falsifying logs is a red flag.
Candidate tipExplain how you plan driving, breaks and rest before you leave, how you use your logging device, and what you do when delays at a dock eat into your hours.
Question 3: Describe your experience handling the different demands of dry vans, reefers, flatbeds or tankers.
Example answerThe interviewer wants to understand which trailers you have actually pulled and how you handled their different loading, handling or monitoring demands.
Start with an honest overview of your trailer experience, including types you have not driven. Then use Situation, Task, Action, Result for one real load: name the trailer and cargo, explain your responsibility, describe your own checks or driving choices, and give the outcome. Close with a lesson you carried into later trips. You do not need experience with every trailer listed.
For example: "Most of my experience is with dry vans, but I have also pulled reefers. On a refrigerated load, I needed to keep the cargo within the temperature range in the shipping instructions. I checked the setting and temperature before leaving and monitored the temperature during the trip. The load arrived within the required range. That trip taught me to check the load instructions rather than assume the last temperature setting was right."
Avoid listing trailer names without explaining their demands, overstating experience with equipment you have not driven, or giving general claims instead of describing your own actions.
Interviewer tipListen for trailer types actually driven and specific handling or load checks, backed by a real load and a lesson learned. Claiming experience with a trailer they have never pulled is a red flag.
Candidate tipName the trailers you've actually pulled and the work each required. Use a real load to show what you did, the result and a lesson you still use.
Question 4: Walk me through a time you backed a trailer up to a loading dock using hand signals from the dock crew.
Interviewer tipListen for how the driver used the crew's signals and checked the trailer's final position. Continuing to back after losing sight of the person giving hand signals is a red flag.
Candidate tipDescribe the dock layout and how you kept the person signaling in view as you backed in. End with how you checked that the trailer was lined up with the dock before the crew got started.
Question 5: Share an example of a time a cargo securement check caught something you needed to fix before driving on.
Interviewer tipListen for what the driver physically checked, the loose or damaged securement they found and the recheck after correction; judging securement only from the cab is a red flag.
Candidate tipUse a real load check. Name the freight and securement, explain the fault you found and your part in correcting it, then say how you confirmed the load was secure.
Question 6: Describe a time you caught conflicting freight details in the load paperwork before leaving the shipper.
Interviewer tipA useful example identifies the conflicting entries, the driver's own checks and how the paperwork was corrected; knowingly leaving with false load details is a red flag.
Candidate tipChoose one paperwork mismatch, such as a different destination or trailer number. Focus on what you checked, who confirmed the correct details and what was fixed before departure.
Question 7: What checks confirm that a trailer is fully coupled to the tractor before you raise the landing gear?
Interviewer tipListen for a visual check of the fifth-wheel jaws around the kingpin, no gap at the plates and a controlled tug test; relying on the sound of the lock alone is unsafe.
Candidate tipDescribe your visual inspection of the fifth wheel and kingpin, then the controlled tug test with the trailer brakes holding. Explain why a click alone does not confirm a secure coupling.
Question 8: Walk me through how you lower the landing gear to support a loaded trailer before uncoupling.
Interviewer tipExpect checks of the ground, landing gear feet and stable support before separating the tractor; uncoupling with the trailer unsupported is a serious error.
Candidate tipDescribe how you secure the rig, judge the ground under the landing gear and crank the legs into position. Explain how you confirm the trailer can be supported before uncoupling.
Question 9: What safety checks do you make before pulling out with a load of hazardous materials?
Interviewer tipA strong answer checks that the shipping papers and the required hazard signs on the truck match the load. Driving off with a known mismatch is a red flag.
Candidate tipGo through your checks before departure, from matching the shipping papers to the load to checking the required placards, the hazard signs on the truck. Give an example of a mismatch you'd get corrected before leaving.
Question 10: Before you head to a stop you've never been to, how do you confirm the delivery instructions and the route?
Example answerThe interviewer wants to know that you check the details before you leave, so you arrive at the right place, on time and by roads a truck can use.
Explain where your instructions come from, what you verify, and how you plan the last few miles.
Sample answer: "I start with the bill of lading and dispatch's notes, and I check that the address, appointment time and any reference numbers match. For a new stop, I check the receiver's current written instructions for receiving hours, the truck gate and where trucks wait. If anything is missing or unclear, I call the receiver or ask dispatch to confirm it. Then I plan the route in a truck GPS and check it against a road atlas, looking for low clearances, weight limits and roads trucks can't use. The last few miles are where trouble usually happens, so I look at the area on a map ahead of time. If anything doesn't match, I ask dispatch before I leave, not when I'm already lost."
Pitfalls to avoid: relying on a car navigation app alone, leaving receiving hours or dock access unconfirmed, and assuming the paperwork is right without checking it.
Interviewer tipListen for checking the bill of lading and dispatch notes, calling ahead about hours and dock access, and checking truck routes; trusting a car map app alone is a red flag.
Candidate tipExplain where you get the instructions, how you double-check the address, appointment time and dock details, and how you make sure the roads allow trucks.
Question 11: Walk me through how you chose a fuel-efficient, truck-safe detour when weather, a closure or traffic disrupted a trip.
Interviewer tipA strong example connects truck GPS or map checks to clearances, weight limits, fuel use and the trip's outcome. Following a car GPS onto a truck-restricted road is a red flag.
Candidate tipPick one disrupted trip. Explain the truck GPS, map or dispatch information you used, your route choice, its effect on fuel and delivery, and what you learned.
Question 12: Tell me about your qualifications and driving experience for tractor-trailers or other heavy trucks.
Interviewer tipListen for the CDL class and endorsements they hold, the trucks they have driven and clear limits on their experience. Claiming a license or endorsement they do not hold is a red flag.
Candidate tipState your CDL class and any endorsements, then describe the trucks, routes and loads you have handled. Distinguish supervised training from work experience.
Question 13: Describe how you secured a load by hand on a recent trip, using straps, chains, binders or tarps.
Interviewer tipLook for the number and placement of tiedowns, edge protection, and rechecking the load early in the trip; saying it looked fine without checking again is a red flag.
Candidate tipPick a real load and say what it was, how many tiedowns you used and where, how you protected edges, and when you stopped to recheck it on the road.
Question 14: Tell me about a time you found a defect or damage on your truck and had to report it.
Example answerThe interviewer wants to know whether you report truck defects honestly and make a sound decision about safe operation.
Use Situation, Task, Action, Result. Describe what you found, how you reported it, how the safety decision was made and what happened afterward. If you have not encountered a defect, say so and offer a truthful training or inspection example.
Sample answer: "During a post-trip inspection, I heard an air leak at a trailer connection. I recorded the defect, contacted the shop and told dispatch that the trailer needed evaluation before another run. The mechanic confirmed the repair was needed and replaced the damaged seal. Before using the trailer again, I checked the repair documentation and completed my pre-trip inspection. Dispatch adjusted the next assignment while the work was done."
Avoid hiding damage, continuing with an unsafe or out-of-service defect, or assuming every minor defect requires the same response. Explain how you followed the reporting and safety requirements that applied rather than inventing an incident to sound experienced.
Interviewer tipLook for a written report, a sound safety decision and follow-up with the shop. Hiding damage or driving with an unsafe or out-of-service defect is a red flag.
Candidate tipSay what you found, how you decided whether the truck could be driven, how you reported it in writing, and what the shop did about it.
Question 15: What does a bill of lading tell you about the freight you are assigned to haul?
Interviewer tipA competent answer identifies the shipper, consignee, freight description, quantity and listed weight; treating the bill of lading as only a delivery address misses its purpose.
Candidate tipWalk through the assignment details you read on a bill of lading. Connect each detail to understanding the shipment, and distinguish listed freight weight from the truck's total weight.
Question 16: When you pick up a load, how do you confirm the piece count and condition before you sign for it?
Example answerThe interviewer wants to know that you protect yourself and the company by checking freight before you take responsibility for it.
Walk through the steps you follow at pickup and what you do when something doesn't match.
Sample answer: "When the dock finishes loading, I count the pieces or pallets against the bill of lading before I sign. I look for crushed boxes, broken wrap, leaks or wet spots, and I make sure what's on the trailer matches the paperwork. If the shipper loaded and sealed the trailer and I couldn't watch, I note 'shipper load and count' on the bill of lading. If the count is short or something is damaged, I write it on the paperwork before signing, take photos if the company allows it, and call dispatch so they can sort it out with the shipper. That way any problem is on record before I leave the dock."
Pitfalls to avoid: signing for a count you could not verify without documenting that limit, leaving damage or shortages off the paperwork, and failing to notify dispatch about discrepancies.
Interviewer tipStrong answers mention counting against the bill of lading, checking for damage, and noting shortages on the paperwork before signing; signing first and checking later is a red flag.
Candidate tipExplain how you count, what damage you look for, and how you note problems on the bill of lading. Mention when you would call dispatch before signing.
Question 17: Tell me how you handled a delivery when the receiver would not sign the delivery receipt.
Interviewer tipThe example should show why the signature was refused, what the driver did and how delivery was documented; signing the receiver's name for them is unacceptable.
Candidate tipSet up one real delivery briefly. Explain your conversation with the receiver, any help you sought from dispatch and how the receipt issue ended.
Question 18: What would you do if an open weigh station's signs directed trucks to enter but your cab device gave no clear bypass instruction?
Interviewer tipThey should follow the station's signs and enter safely unless clearly authorized to bypass; assuming silence from the cab device means permission to pass is a red flag.
Candidate tipStart with the posted entry direction. Explain how you would approach the station safely and follow its lane signals without guessing that the device granted a bypass.
Question 19: What would you do if a pallet you needed to unload weighed more than the truck's liftgate could safely carry?
Interviewer tipThe load must stay off the overloaded liftgate while they arrange equipment rated for it; trying the lift anyway because the pallet fits is unsafe.
Candidate tipExplain your first move to prevent an overloaded lift. Then describe how you would confirm the pallet's weight and arrange a safe unloading method with the receiver or dispatch.
Question 20: Give an example of how you handled routine truck maintenance that could not wait until the next scheduled service.
Interviewer tipSeek a specific maintenance need, the driver's own work and a check that it was resolved; opening a hot cooling system or attempting work beyond their training is a red flag.
Candidate tipPick a real job such as topping up oil or replacing a light. Explain the truck's condition, the precautions you took, the work you did and the check afterward.
Question 21: How do you remind yourself to check conditions of trailers after contents have been unloaded to ensure that there has been no damage?
Question 22: Talk about a time you used a cab computer, radio or phone to clear up a confusing message from dispatch.
Interviewer tipA strong case shows the unclear message, the driver's reply and confirmation of the corrected information; typing on a phone while driving is a red flag.
Candidate tipDescribe the message and the device you used. Focus on how you communicated safely, confirmed what dispatch meant and avoided acting on the wrong information.
Question 23: Tell me how you responded when a gauge reading, unusual smell or change in handling alerted you to a truck problem on the road.
Interviewer tipThe example should show how the driver judged the warning, stopped safely when needed and arranged help before continuing. Ignoring a warning of a serious truck fault to meet a delivery window is a red flag.
Candidate tipChoose a real truck warning. Explain what you noticed, your own response, any checks or calls to the shop or dispatch, and the result. End with what the incident taught you.
Question 24: Give an example of how you handled a difficult receiver, shipper or dispatcher while picking up or delivering a load.
Interviewer tipListen for the driver's own calm actions, a clear outcome for the load and a lesson about working with the receiver, shipper or dispatcher. Threatening someone over a delay is a red flag.
Candidate tipChoose one real disagreement during a pickup or delivery. Briefly explain the issue, focus on your own words and actions, and end with the outcome for the load and what you learned.
Question 25: Describe methods you have found effective to follow special cargo-related procedures, such as checking refrigeration systems for frozen foods or providing food or water for livestock.
Question 26: How do you use a truck route map to choose fuel stops on a route with few places that can accommodate a tractor-trailer?
Interviewer tipExpect fuel-range estimates, road distances, and checks of truck access and route restrictions. Choosing a stop by straight-line distance without checking the truck route risks leaving the rig short of fuel.
Candidate tipTrace the truck route and possible fuel stops on the map. Explain how you compare road miles with fuel range and check that the roads and stops can accommodate your rig.
Question 27: Recall a time you had to clear debris from a loaded trailer with little room to work.
Interviewer tipLook for the driver's safe access plan, actual removal method and result; climbing on unstable freight or pulling out load securement to reach trash is a red flag.
Candidate tipName the debris and what blocked access. Describe how you removed it while keeping the freight secure, including any help you needed, and the condition you left the trailer in.
Question 28: Walk me through how you check all load-related documentation to ensure that it is complete and accurate.
Question 29: Are you familiar with equipment, such as truck cab computers, CB radios, and telephones, to exchange necessary information with bases, supervisors, or other drivers?
Question 30: Describe an experience when you loaded and unloaded trucks, or helped others with loading and unloading, operating any special loading-related equipment on vehicles and using other equipment as necessary.