Field Service Technician Interview Questions
For robotics technicians who install and maintain robots on automated production lines. Interviews focus on tracing faults, testing repairs and calibrating robotic equipment.
30 questions, ranked by what the job needs most
In other fields: Control and Valve Installers and Repairers, Except Mechanical Door · Electrical Engineering Technicians · Coin, Vending, and Amusement Machine Servicers and Repairers · all 11 sets →
Print the top 10:Scoring sheetPractice sheet
Question 1: Walk me through a difficult robot fault you traced to an electrical, mechanical, pneumatic or program issue.
Example answerThe interviewer wants to learn whether you use evidence to solve a difficult robot fault instead of guessing at parts.
Build your answer around Situation, Task, Action, Result. Briefly describe the robot's symptoms and your responsibility for the repair. Spend most of the answer on your checks, why you chose them, and how the findings ruled out possible causes. End with evidence that the repair worked and a lesson from the diagnosis.
For example: "The robot intermittently dropped parts during a transfer. I needed to find the fault before the cell could return to production. The program showed the expected grip command, but the pressure reading dropped when the gripper operated. After isolating the equipment safely, I found a damaged air line. I replaced it and checked for leaks. Controlled test cycles showed stable pressure and a secure grip. I learned to compare the command with the physical response before blaming the program."
Avoid listing tests without explaining their purpose, claiming a fix without checking it, or describing only what the team did.
Interviewer tipListen for tests that narrowed the fault, evidence that the repair worked, and a lesson from the diagnosis. Replacing robot parts without checking the cause is a red flag.
Candidate tipChoose one difficult robot fault. Explain the symptoms, the checks you used to rule out causes, and your repair. Finish with the test results and a lesson for your next diagnosis.
Question 2: Walk me through a maintenance job where you addressed wear on a production robot.
Interviewer tipListen for a clear link between the wear they found, the work they did, and the check they made before returning the robot to service. Skipping that check is a red flag.
Candidate tipName the part that showed wear and the clue you noticed, such as looseness or unusual noise. Describe the maintenance you performed and the check that told you the part was ready for use.
Question 3: Describe a time you got a conveyor controller working as part of a robotic production line.
Interviewer tipA strong answer explains the technician's work on the controller and how they checked that the conveyor fed parts when the robot was ready. Releasing the line while the conveyor feeds too early is a red flag.
Candidate tipSay what you installed, set up, or repaired on the conveyor controller. Describe the signal you checked between the conveyor and the robot to confirm that parts arrived when the robot was ready.
Question 4: Describe a time you adjusted a robot's taught positions after a fixture or part location changed.
Interviewer tipTheir example should show controlled changes to taught points and safe testing of the affected motion. Running the changed positions at full production speed without checking clearances is a red flag.
Candidate tipChoose one fixture or part location change. Explain the taught points you changed, the precautions you took, and the checks that confirmed correct motion. End with the result and a lesson from the adjustment.
Question 5: Share an example of programming a robotic cell to switch between parts that needed different handling sequences.
Interviewer tipListen for the sequence the candidate programmed for each part and a test that included switching between them. A red flag is leaving the controller able to run the previous part's sequence after a switch.
Candidate tipA robotic cell includes the robot and the equipment it works with. Explain how your program selected the right moves for each part and what you saw when you tested a switch between parts.
Question 6: Give an example of how you taught a robot to pick up a part from a fixture and set it down in a tray.
Interviewer tipListen for how they taught the pickup and release positions and checked them in a full run. Assuming the task works because the robot can reach each point on its own misses what happens between them.
Candidate tipA robotics lab example works here. Explain how you set the pickup position at the fixture, the holder for the part, and the release position at the tray, then checked the full move.
Question 7: What would you do if a replacement robot sensor fit the mounting bracket but had a different output type?
Interviewer tipThe sensor's output must match the controller input or be supported by a verified change. Treating a physical fit as proof of electrical compatibility is a red flag.
Candidate tipStart with keeping the cell out of service while you compare the sensor specifications with the controller input requirements. Explain how you would resolve the mismatch before testing the repair.
Question 8: What checks do you make when wiring connections between a robot controller and another controller?
Interviewer tipExpect hazardous energy control, checks of wiring diagrams and connector pinouts, and connection tests before startup. Guessing terminal assignments from wire color alone is a red flag.
Candidate tipWalk through wiring between the controllers from energy isolation to checking diagrams, cable connections, and signal compatibility. Explain the tests you make before putting the connection into service.
Question 9: How have you tested whether a robotic assembly could place parts within tolerance over repeated cycles?
Interviewer tipLook for a placement limit, a way to measure where the parts landed, and results from several runs. Calling the assembly ready after one good placement misses the repeatability test.
Candidate tipState the tolerance, or allowed placement error, and describe how you measured where parts landed over several runs. Say what the readings showed about whether the assembly met that limit.
Question 10: Tell me how you lined up a gripper and its mounting plate during a robot build.
Interviewer tipListen for the feature or tool they used to line up the gripper and the check they made after fastening it. Forcing misaligned parts together with the bolts is a red flag.
Candidate tipThe gripper is the tool that holds the part. Name the feature or tool you used to line it up with the mounting plate and how you checked that the two surfaces sat flush after fastening.
Question 11: Share an example of how you documented a robot test so another technician could repeat it.
Interviewer tipA strong example shows their own work recording the setup, steps, and results so a technician could repeat the test. A note that only says 'passed' gives no usable test procedure.
Candidate tipUse one robot test you documented. Describe the setup, settings, steps, and results you recorded, then show how another technician used the record. Include anything you learned about making test instructions clear.
Question 12: Describe an effective robotic device or system which you built or assembled.
Question 13: Walk me through a time you corrected an alignment problem while installing a robot on a base or track.
Interviewer tipListen for checks against mounting drawings, a safe correction, and proof the robot was secure. Improvising anchors without checking mounting requirements is a red flag.
Candidate tipPick an installation with a base or track alignment problem. Describe your checks against the mounting drawings, your role in the correction, and the final checks. Close with the result and what you learned.
Question 14: Share an effective method you have used to evaluate and maximize the efficiency and reliability of industrial robotic systems.
Question 15: Describe a robotic path motion you developed which successfully maximized efficiency, safety, or quality.
Question 16: Tell me about a time when you successfully trained personnel or customers on the installation, use, or maintenance of robots. What methods made you successful?
Question 17: Share an experience in which you effectively assisted an engineer in design, configuration, or application of a robotic system.
Question 18: What factors do you consider when inspecting installation sites?
Question 19: Tell me about your experience fabricating housings, jigs, fittings, and/or fixtures.
Question 20: Describe an effective three-dimensional simulation of an automation system which you developed.
Question 21: Describe a time you successfully tested or calibrated a robot's position feedback system.
Example answerThe interviewer wants to learn whether you can test or calibrate electronic position feedback and confirm that the robot meets the required checks.
Use Situation, Task, Action, Result to organize one real example. Name the feedback device and your responsibility. Explain the service instructions, safety steps and test or calibration checks you used. Finish with the recorded result and what you learned.
For example: "After maintenance, I was assigned to check a robot's encoder feedback before it returned to service. I followed the service instructions and used the required safeguards for the checks. I compared the reported position with the specified reference positions and recorded the results. One position was outside the allowed limit. I followed the prescribed calibration procedure, then repeated the position checks under controlled conditions. The readings met the limits. I learned to repeat the full check after an adjustment instead of assuming the first corrected reading proved the job was complete."
Avoid treating a cleared alarm as proof of accurate feedback, skipping required reference checks or testing robot motion without the required safeguards.
Interviewer tipA strong example shows their own testing or calibration of an encoder or other feedback device and evidence that it met the required checks. Treating a cleared alarm as proof of accurate position feedback is a red flag.
Candidate tipChoose one real test or calibration. Name the feedback device, your responsibility, the service instructions and checks you used, and the result. Explain what you learned about confirming robot position feedback.
Question 22: Share an example of how you traced and repaired a mechanical robot problem involving a gearbox, belt or end-of-arm tool.
Example answerThe interviewer wants to learn whether you can connect mechanical symptoms to a cause and make a safe, effective robot repair.
Choose one case and use Situation, Task, Action, Result. Set out the symptom and your repair responsibility briefly. Explain the physical evidence, the safety steps before inspection, and your own repair work. Close with the checks that showed the problem was resolved and a lesson you took forward.
For example: "A belt-driven robot axis started making noise and placing parts inconsistently. I was assigned to find the mechanical cause. After isolating hazardous energy and securing the axis as required, I inspected the drive and found a damaged belt. I replaced it and set the tension according to the service instructions. Controlled tests showed smooth travel and consistent placement. I learned to include belt condition in my checks when noise and position errors appear together."
Avoid blaming a gearbox or belt without inspection evidence, leaving out hazardous energy control, or describing the replacement without explaining how you tested the robot afterward.
Interviewer tipStrong examples connect signs such as noise, play or vibration to the mechanical fault and show a tested repair. Working on the robot without controlling hazardous energy is a red flag.
Candidate tipChoose a real mechanical robot repair. Explain the evidence that led you to the cause, your safety steps, and the work you did. Close with the test result and a lesson you took from the repair.
Question 23: Share an experience in which your attention to detail and thoroughness had an impact on your last company.
Example answerThe interviewer wants proof that you catch errors others miss and that this protects the organization.
Use Situation, Task, Action, Result. Describe what you were checking, what you noticed, and how you found it, such as comparing against a source or double-checking totals. Then explain what would have happened if the error had gone through, and what you did to prevent it next time.
Sample answer: "While preparing an order for a large customer, I compared the quantities against the signed quote, as I always do, and saw that one item had been entered as 1,000 units instead of 100. I flagged it to my supervisor, we corrected it before it shipped, and we avoided a costly return. Afterward I suggested adding a quote-check step to the order form, and the team adopted it."
Pitfalls: Don't just say you're detail-oriented without an example. Avoid exaggerating the dollar impact. Don't describe perfectionism that caused missed deadlines.
Question 24: Tell me about a time a routine inspection of a robot, such as checking cables, hoses or gear backlash, helped you catch a problem before it caused downtime.
Example answerThe interviewer wants to know you inspect with purpose and can spot wear before it stops production. Use Situation, Task, Action, Result. Say what you were inspecting and why, what you noticed, what you did, and how the issue was addressed before a breakdown. Avoid claiming you proved a future failure would have happened. Sample answer: During a weekly check on a welding robot, I noticed the outer jacket on the dress pack cable was rubbed through near the upper arm. Nothing had failed yet, but the wires inside were starting to show. I used the cell's safe stopping procedure immediately, kept people clear and notified the supervisor. I followed lockout and verified isolation before inspecting the damage closely. The cell stayed out of service while I replaced the damaged cable and adjusted its guide. I logged the repair and added the same cable wear check to the inspection list for the other robots on the line. Pitfalls: describing a breakdown instead of something you caught early, claiming results you cannot back up, and leaving out how you recorded what you found.
Interviewer tipA strong answer shows they inspect with purpose and know common wear points, like dress packs. Inspections done only after a breakdown are a red flag.
Candidate tipDescribe what you were checking, what looked wrong, and what you did about it. Say what could have happened if the problem had been missed.
Question 25: Give an example of how you acted on robot error logs or cycle time data that showed an emerging problem.
Example answerThe interviewer wants to learn whether you notice warning patterns in robot data and take useful action before the problem grows.
Use Situation, Task, Action, Result for one real example. Identify the logs or cycle time data, the pattern that caught your attention, and your responsibility. Explain your investigation and response, then give the observed result and what you learned. Distinguish a confirmed result from a breakdown you only think you prevented.
For example: "While reviewing robot alarm history, I noticed repeated part-present faults at one pickup point. The cell usually recovered on a retry, so the issue had not stopped production for long. I checked the sensor readings during controlled testing and found that a loose bracket let the sensor shift. After securing and aligning it, I tested the pickup sequence and checked later alarm history. The repeat faults stopped appearing during those checks. I learned to investigate repeated short interruptions even when the robot recovers."
Avoid listing alarms without identifying a pattern, clearing repeat faults without investigation, or claiming you prevented a breakdown without evidence.
Interviewer tipA strong example links a pattern in robot logs or cycle times to their investigation and its result. Clearing repeated alarms without investigating the pattern is a red flag.
Candidate tipIdentify the robot data you reviewed and the pattern you noticed. Focus on your investigation and response, then explain the result and what you learned about spotting problems early.
Question 26: What is the state of your service records? What is something you would like to improve?
Question 27: How do you plan and prioritize your work when several robot cells need repairs or preventive maintenance at the same time?
Example answerThe interviewer wants to see how you decide what comes first when the work piles up. Explain how you rank the work, then give an example of a busy shift. Safety issues usually come first, then faults that stop production, then preventive maintenance and smaller jobs. Show how you keep planned work from slipping. Sample answer: I start each shift by checking open work orders and the maintenance schedule, and I talk with the lead about what production needs that day. One shift, a robot on the main line went down while two other cells had preventive maintenance due. I took the line-down fault first, since the whole line was waiting, and asked the other technician to start the first PM. Once the robot was back up, I moved the second PM to the planned break so production would not lose more time. I logged everything so the next shift knew what was done and what was still open. Pitfalls: saying everything is urgent, never mentioning safety, and leaving out how you tell others when the plan changes.
Interviewer tipListen for priorities set by production impact and safety, and for planned maintenance scheduled around shifts. Letting PMs slip every time a fault comes up is a red flag.
Candidate tipExplain how you rank the work, such as safety first, then line-down faults, then PMs. Give one real example of a busy shift and how you sorted it out.
Question 28: Describe a time you told a production manager that a robot line would be down longer than expected.
Interviewer tipTheir example should show a prompt update, a clear explanation of the delay, and honesty about uncertain repair times. Hiding a known delay until the promised restart time passes is a red flag.
Candidate tipPick one robot line delay. Describe when you updated the production manager, the facts you shared, and how you handled uncertainty about restart time. End with the result and a lesson about giving bad news.
Question 29: Tell me how you handled pushback from a production supervisor or operator when you needed to shut down a robot cell.
Interviewer tipA useful example shows how they listened to production concerns, explained the need to stop the cell, and reached a safe plan. Agreeing to keep an unsafe cell running is a red flag.
Candidate tipUse a real shutdown disagreement. Explain the supervisor's or operator's concern, your response, and the plan you reached. Include the outcome and what you learned about handling pushback.
Question 30: Tell me about a time when you successfully determined the cause of an operating error at your company and solved the problem.
Example answerThe interviewer wants to see how you track down the real cause of a problem instead of treating only the symptoms.
Use Situation, Task, Action, Result. Describe the error and its impact, the steps you took to narrow down the cause, the fix, and what you did to keep it from happening again.
Sample answer: "Our label printer started putting the wrong dates on some product labels, which meant those items had to be pulled from the shelves. I checked the printer settings first, and they were fine. Then I compared the bad labels and saw they all came from orders entered after a software update. The update had changed the date format in one field. I worked with our IT contact to fix the setting, reprinted the labels, and added a quick label check to our start-of-shift routine."
Pitfalls: Don't stop at the first fix that seemed to work. Avoid blaming coworkers. Don't leave out how you prevented a repeat.
New to interviews? Start with the common questions every interview asks →