Registered Radiologic Technologist Interview Questions
For radiologic technologists who take X-rays or perform diagnostic scans. Interviews focus on setting up scans, operating imaging equipment and checking image quality.
30 questions, ranked by what the job needs most
Print the top 10:Scoring sheetPractice sheet
Question 1: What would you do if a staff member stayed in the x-ray room without protection as you were about to make an exposure?
Interviewer tipThe exposure should wait until the staff member leaves or has the protection needed for their role. Exposing first and warning them afterward is a red flag.
Candidate tipBegin with what you would do before pressing the exposure switch. Explain how you would address the staff member and confirm the room is safe before proceeding.
Question 2: What would you do if a patient with a suspected knee fracture could not bend the knee for the requested x-ray views?
Interviewer tipExpect them to avoid forcing the knee, assess safe positioning options and consult the radiologist if the requested views cannot be obtained. Moving through severe pain just to match a routine view is a red flag.
Candidate tipExplain your first safety check, then how you would use support or an alternate view within the exam instructions. Say when you would seek the radiologist's direction rather than force the position.
Question 3: When you review an image before sending it to the radiologist, what do you check to decide whether it needs to be repeated?
Example answerThe interviewer wants to know whether you check an image's technical adequacy for diagnostic use and repeat only when needed, within your role and department protocol. Name the checks you run on every image, then show your judgment with an example. Sample answer: "On each image I check that the whole area of interest is included, that positioning matches the protocol, and that there is no rotation or motion. I look at exposure, noise and contrast, and for artifacts such as jewelry or a gown snap. I also confirm the side marker and patient details. Once, on a lateral knee, the joint space wasn't open because the knee was slightly rotated, so I adjusted and repeated that one view. Another time a hand image had a small artifact well away from the injured finger, so I asked the radiologist, who said it was fine to send. Each repeat adds dose, so I want a clear reason first." Pitfalls to avoid: repeating out of habit; sending a poor image to avoid a repeat; forgetting markers and patient details.
Interviewer tipA strong answer names anatomy coverage, positioning, exposure, motion, artifacts and markers, and weighs a repeat against extra dose; repeating by habit is a red flag.
Candidate tipList the checks you run on every image and give an example of one you repeated and one you judged diagnostic as is. Show that you weigh image quality against patient dose.
Question 4: Walk me through a routine x-ray exam you perform, from reading the order to sending the images for the radiologist to read.
Example answerThe interviewer wants to see that you follow a safe, complete routine on every exam, not only that you can work the equipment. Build the answer in order: check the order, identify the patient, explain the exam, protect from radiation, position, set technique, check the images, and send them. Sample answer: For a two-view chest exam, I first read the order and the reason for the exam. I bring the patient in and confirm their name and date of birth against the order, then ask about possible pregnancy when our policy calls for it. I explain what I'll do and how they'll need to breathe. I position them for the PA view, center the beam, collimate to the chest and set the technique for their size. I take the image on full inspiration, then do the lateral. Before the patient leaves, I check that the lungs are fully included, there's no rotation or motion, and the markers are right. Then I send the images to PACS for the radiologist. Pitfalls to avoid: skipping patient identification; leaving out the image check; listing steps without saying why they matter.
Interviewer tipA strong answer covers checking the order, identifying the patient, radiation protection, positioning, technique and an image check before sending; skipping patient identification is a red flag.
Candidate tipChoose one common exam, such as a chest or ankle series, and go step by step. Mention two patient identifiers, radiation safety, and how you check the images before sending them.
Question 5: Tell me how you talked an uneasy patient through a scan while checking that they were safe and comfortable.
Interviewer tipListen for how the technologist told the patient what to expect and responded to signs of discomfort during the scan. Continuing after the patient asked to stop is a red flag.
Candidate tipUse one scan to show what you told the patient to expect, how they could signal discomfort, and what you did when you noticed a concern. End with how the patient responded.
Question 6: Walk me through how you set the X-ray tube distance and exposure time for an exam you performed.
Interviewer tipA strong answer ties the tube distance and exposure time to the view the exam called for. Reusing the previous exam's settings without checking them is a red flag.
Candidate tipName the body part and view. Explain how the exam protocol guided the exposure time and how you confirmed the distance from the X-ray tube to the image detector before taking the image.
Question 7: Share an example of how you changed exposure settings to reduce motion blur on an x-ray.
Interviewer tipListen for a reasoned change in exposure time and related settings, its effect on image quality and a lesson. Increasing dose without considering the cause of blur is a red flag.
Candidate tipChoose one exam affected by movement. Explain the settings you changed, why they fit that patient and exam, and the resulting image quality. Include what you would carry into the next exam.
Question 8: Share an example of how you changed your breathing instructions when a patient could not follow them during an x-ray.
Interviewer tipListen for the words or demonstration they used, the patient's response and the effect on the image. Repeating the same instruction louder without checking understanding is a warning sign.
Candidate tipChoose one exam. Explain the breathing difficulty, how you changed your instructions and whether the patient could follow them. Include a lesson you used in later exams.
Question 9: Recall a situation where you traced an unexpected artifact on an x-ray image to its source.
Interviewer tipA useful example links the artifact's appearance to checks that found its source and a verified result. Automatically repeating the exposure without investigating is a red flag.
Candidate tipDescribe the artifact and how you worked out whether it came from the patient, detector or processing. Explain your own checks, the result and a lesson for reviewing later images.
Question 10: Describe a time you rejected an x-ray view after checking its image quality.
Interviewer tipThe example should explain the unmet image criterion, the change before repeating the view and the repeat's result. Rejecting a diagnostically adequate view merely for a cosmetic flaw is a red flag.
Candidate tipChoose one rejected view. Explain the image criterion it failed, your correction before the repeat and how you checked the new view. End with what you learned about avoiding further repeats.
Question 11: What do you ask a patient before an imaging exam to make sure the history you record is accurate and complete?
Example answerThe interviewer wants to know that you collect the history the radiologist needs and catch safety issues before the exam. Explain the questions you ask and why each one matters, then how you record the answers. Sample answer: After I confirm the patient's identity, I ask why they're here in their own words, where the pain or problem is, and when it started, so the history matches the order and I image the right area. I ask about past surgery, implants and prior imaging, since the radiologist may want to compare. I ask about possible pregnancy before the exams that need it, following our facility's policy. Before any contrast exam I ask about allergies and past reactions. I record the answers in the exam notes, in the patient's own words where I can. If the history doesn't match the order, I check with the ordering provider before I start. Pitfalls to avoid: reading the order back instead of asking; skipping pregnancy or allergy questions; leaving the history out of the record.
Interviewer tipListen for the reason for the exam, symptoms, prior imaging, possible pregnancy where relevant, allergies and implants; reading only the order and asking nothing is a red flag.
Candidate tipWalk through your usual questions and explain why each matters, such as pregnancy status before certain exams or allergies before contrast. Mention how you record the answers.
Question 12: Tell me about a time you obtained a useful imaging history from a patient who had trouble describing their symptoms.
Interviewer tipListen for patient-led descriptions, focused clarification and an accurate history passed on for the exam. Filling gaps with symptoms the patient never reported is a red flag.
Candidate tipUse one anonymous case. Explain how you helped the patient describe the location and timing of symptoms, what you recorded and how it helped the exam. Add a lesson about asking clearer questions.
Question 13: Share an example of how you sorted out conflicting information from an exam order, the patient's chart and the patient before an imaging exam.
Interviewer tipThe example should show how they weighed the order, chart and patient's account, resolved the mismatch and learned from it. Proceeding on a guess about the exam or body part is a red flag.
Candidate tipUse a real mismatch between an exam order, chart and patient's account. Explain which details mattered, your checks and who helped clarify them. Finish with the exam outcome and a lesson for checking future orders.
Question 14: What details in an x-ray request help you decide which views the exam needs?
Interviewer tipThe answer should connect the body part, side, clinical reason and requested views to the exam protocol. Guessing at an unclear side or changing the ordered exam without clarification is a red flag.
Candidate tipWork through a sample request. Connect its body part, side and clinical reason to the views required, and identify any missing detail you would clarify before starting.
Question 15: Describe a time you prepared and gave a patient oral or injected contrast for an imaging exam.
Example answerThe interviewer wants to know how you safely prepared and administered contrast in a case you actually handled. Use Situation, Task, Action, Result. State your role, the screening and preparation checks, how contrast was given, and the patient's response. Check state rules and facility requirements when describing duties that depend on scope.
Sample answer: "For an exam using oral contrast, I checked the order and confirmed the patient's identity. I reviewed the required screening information and referred any concerns to the radiologist before proceeding. I checked the ordered agent, amount and timing, prepared it according to our protocol, and explained the drinking instructions. I gave the contrast within my assigned role, checked that the patient could follow the instructions, and monitored for symptoms or difficulty tolerating it. I documented what was given and the patient's response."
Avoid turning the answer into a hypothetical, skipping unresolved screening concerns, or claiming injection experience when your experience was with oral contrast. Explain your own actions without suggesting every route or agent needs identical checks.
Interviewer tipExpect an actual case with order and patient checks, correct contrast preparation, administration within their role and monitoring. Giving contrast despite an unresolved screening concern is a red flag.
Candidate tipUse a case within your actual role. Explain screening, preparation, administration and patient monitoring. Check state rules and facility requirements rather than claiming duties you have not performed.
Question 16: What would you do if a contrast container's label did not match the radiologist's order while you were preparing it?
Interviewer tipPreparation should stop while the label and order are checked with the radiologist. Relabeling the container or substituting an agent without authorization is a red flag.
Candidate tipStart with how you would keep the mismatched contrast from being used. Describe the details you would compare and how you would get the radiologist's direction before preparing the dose.
Question 17: What would you do if a patient became short of breath during an imaging exam?
Interviewer tipPatient assessment and an immediate call for medical help should take priority over finishing images. Leaving a distressed patient alone to find help is a red flag.
Candidate tipState your first response to the breathing change. Explain how you would stop the exam, get medical help and report what you observed while staying within your training.
Question 18: Describe an experience when you monitored patients' conditions and reactions, reporting abnormal signs to physician.
Question 19: Give an example of how you handled an imaging equipment problem found during a quality control check.
Interviewer tipLook for the failed check, their action to prevent unsafe use, the report to the supervisor and the outcome. Continuing patient exams despite a failed safety check is a red flag.
Candidate tipName the equipment and failed check. Explain what you personally did about its use and reporting, how the problem was resolved and what the experience taught you.
Question 20: Share an experience in which your diligence of inspecting equipment, structures, or materials helped you identify a problem or the cause of a problem.
Example answerThe interviewer wants evidence that you inspect carefully and that your checks catch problems before they grow.
Use Situation, Task, Action, Result. Say what you were inspecting and why, what you noticed, how you traced the cause, and what happened after you reported or fixed it.
Sample answer: "During a routine walk-through, I noticed a small puddle of fluid under one of our machines. It wasn't on the checklist, but I wiped it up and checked again an hour later, and it was back. I followed the line and found a fitting that had worked loose. I tagged the machine, reported it to my supervisor, and maintenance replaced the fitting before the end of the shift. If it had failed during a full run, we would likely have lost most of a day."
Pitfalls: Don't claim you never miss anything. Avoid stories where you found a problem but didn't report it. Don't skip how you confirmed the cause.
Question 21: Walk me through a time you corrected a processing error in a digital radiograph without making another exposure.
Interviewer tipA strong example separates a processing problem from an acquisition problem and describes the correction and result. Claiming processing can recover anatomy outside the exposed field is a red flag.
Candidate tipName the processing error, such as the wrong exam processing selection. Describe your checks and correction, the resulting image and what you learned about avoiding unnecessary exposures.
Question 22: How do you check that an x-ray series reached the correct patient's exam in the picture archiving system?
Interviewer tipExpect checks of patient identifiers, the exam or accession number, and the full image series in the archive. Assuming a successful send message proves correct filing is a red flag.
Candidate tipDescribe your checks from the imaging workstation through the archived exam. Explain how you confirm the patient, exam and complete series, and what you do if an image is missing or misfiled.
Question 23: Tell me about a time you corrected an error in a patient's imaging exam record.
Interviewer tipListen for how they verified the error, corrected the record with a traceable entry and checked the result. Hiding the original error is a red flag.
Candidate tipUse an anonymous example. Identify the incorrect exam detail, your role in correcting it and how you confirmed the record was accurate. End with a step that helped prevent another error.
Question 24: How do you set up an exam at the imaging console so the scan sequence matches the ordered protocol?
Interviewer tipExpect patient and order checks, correct protocol and sequence controls, and a saved exam record. Running an unrelated preset without checking its settings is a red flag.
Candidate tipWalk through selecting the patient and protocol, entering or checking sequence settings, and saving the exam record. Explain how you catch a wrong selection before taking images.
Question 25: Describe a time you caught a scan sequence entry error at the console before starting an exam.
Interviewer tipListen for the entered value, its mismatch with the requested sequence and the verified correction. Starting the scan before resolving an unexplained mismatch is a red flag; ask what they changed in their checks.
Candidate tipUse one console entry error you found. Explain how you compared it with the requested scan sequence, what you corrected and the result. Finish with a check that helped prevent another entry error.
Question 26: How do you keep track of completed and remaining views during a multi-view x-ray exam?
Interviewer tipA competent answer checks the required views against acquired images and confirms the series is complete before ending the exam. Assuming every exposure produced a usable saved image is a red flag.
Candidate tipWalk through your way of tracking the requested views at the imaging system. Include how you distinguish a completed view from one still needed and confirm that all views were saved.
Question 27: Walk me through a time your exam room setup caught a missing item before the patient arrived.
Interviewer tipA strong example identifies the required item, their check and the effect on exam readiness. Waiting until the patient is on the table to check essential supplies is a red flag.
Candidate tipName the exam and missing item. Describe the room check that caught it, how you made the room ready and the result. Include any change you made to later setup checks.
Question 28: What do you check before transporting a patient from a bed to the x-ray room?
Interviewer tipExpect checks of identity, mobility and fall risk, plus oxygen, lines or other support that must travel with the patient. Disconnecting needed support just to move faster is a red flag.
Candidate tipGo from confirming the patient and destination to checking the safest transport method. Explain how you account for mobility limits, attached equipment and any help needed for the trip.
Question 29: Tell me about the last time you provided assistance in dressing or changing seriously ill, injured, or disabled patients.
Question 30: Recall a time you helped a patient change for an imaging exam while protecting their privacy.
Interviewer tipThe example should show consent, covering and safe help matched to the patient's abilities, with a clear outcome. Exposing the patient unnecessarily is a red flag.
Candidate tipKeep the patient anonymous. Explain the help they needed, how you offered it and protected privacy, and how changing went. Close with a lesson about respectful assistance.
New to interviews? Start with the common questions every interview asks →