Completion Engineer Interview Questions
For petroleum engineers working on oil and gas wells. Interviews focus on drilling and recovery plans, production estimates and whether a well is worth drilling.
30 questions, ranked by what the job needs most
Print the top 10:Scoring sheetPractice sheet
Question 1: How do you decide whether a proposed oil or gas well is worth drilling?
Interviewer tipA strong answer ties the production forecast and price assumptions to the full cost of the well. Using the initial production rate as if it will hold for the life of the well is a red flag.
Candidate tipExplain how you use expected oil or gas prices, production over time, and drilling and operating costs. Name an assumption that could change your decision and explain why.
Question 2: Describe a time you prioritized rework candidates across an oil or gas field with limited workover capacity.
Interviewer tipA strong example compares expected production gains, costs and workover limits, then gives the result of the chosen sequence. Ranking wells by lost output alone misses whether rework will help.
Candidate tipChoose real wells competing for workover capacity. Explain your ranking and the evidence for expected gains. End with the production result and a lesson about prioritizing rework.
Question 3: Walk me through a well modification or stimulation job you'd lead to improve oil or gas recovery.
Interviewer tipA strong plan connects the well's production history to the work and sets pressure limits the crew can monitor. Pressing ahead after a reading exceeds the job's pressure limit is a red flag.
Candidate tipStimulation means treating the rock around the well to help oil or gas flow. Start with the well data that would guide the work, then describe the limits you'd give the crew and the readings you'd watch during the job.
Question 4: Describe how you've used reservoir data to recommend a well location or a way to increase production.
Interviewer tipListen for a specific pattern in the measurements or production records that led to the recommendation. Assuming the whole field behaves like one well without checking other evidence is a red flag.
Candidate tipUse an example from work or a reservoir engineering project. Name the well measurements or production records you used and show how they shaped your recommendation.
Question 5: What would you do if a well test approached the pressure limit set in the test program?
Interviewer tipThe answer should put keeping the test within its pressure limit first, with clear communication to the test crew. Continuing past the limit to finish collecting data is a wrong first move.
Candidate tipStart with how you would keep the test within its limits and communicate with the test crew. Then explain how you would use pressure readings to decide whether the test could safely resume.
Question 6: Walk me through a field plan you developed that covered oil or gas drilling, product recovery and treatment.
Example answerThe interviewer wants to see how you connect drilling plans with product recovery and treatment needs across an oil or gas field.
Use Situation, Task, Action, Result. Identify the field and your responsibility, then explain the data, options and constraints behind the plan. Cover all three parts and close with the results or changes made as new information arrived.
For example: "On a gas field, I used the geology team's maps and well-test results to compare well locations and development timing. I worked with the reservoir team on expected recovery and with facilities engineers on gathering capacity and treatment options based on gas composition and delivery requirements. We compared the costs and chose a phased plan so early well results could inform later drilling. As production data came in, we checked it against the forecast and adjusted the next phase."
Avoid describing only well spacing, leaving treatment to an unexplained assumption or presenting a textbook process without your own contribution.
Interviewer tipA strong example links drilling decisions with recovery methods and treatment needs using field data and costs. Ignoring treatment needs when planning production is a red flag.
Candidate tipChoose one real field plan. Explain your role, the data and options behind the drilling, recovery and treatment choices, and how the plan held up or changed as results came in.
Question 7: What checks do you make before finalizing a well's daily drilling or production record?
Interviewer tipListen for checks on well identity, dates, units and agreement with source readings or field reports. Filling gaps with guesses makes the record unreliable.
Candidate tipWalk through one kind of daily well record. Name the source records you compare, the errors you check for and how you handle missing or conflicting entries.
Question 8: What has been the hardest part of helping a field crew figure out why a producing well's flow rate changed unexpectedly?
Interviewer tipListen for what made the problem hard to pin down, such as a pressure reading that did not fit the flow trend. Settling on a cause before checking whether the readings are reliable is a red flag.
Candidate tipThink of an unexpected change in flow. Explain what made it hard to trace, which readings or operating changes you checked with the crew, and what you narrowed it down to.
Question 9: Share an example of how you worked with a test team to resolve a problem with an oilfield equipment design.
Interviewer tipListen for the candidate's part in turning a specific test result into a design decision. Dismissing a failed test without looking into the cause is a red flag.
Candidate tipAn internship or design project can work. Explain what the test showed, what you contributed to the discussion with the test team, and how the team resolved the design issue.
Question 10: Share an example of how you explained an uncertain well-test result to the field crew.
Interviewer tipListen for the candidate's explanation of the readings, their limits and the crew's understanding. Presenting an uncertain interpretation as a confirmed finding is a red flag.
Candidate tipUse one well test whose meaning was unclear. Describe what you told the field crew, how you explained the uncertainty and what showed they understood. Note what you learned from the exchange.
Question 11: Tell me about a time you kept a field development study moving when one team's input was late.
Interviewer tipLook for a real dependency, the candidate's work to agree on a revised handoff and the study's outcome. Using guessed inputs as confirmed team findings is a red flag.
Candidate tipIdentify the late input and the study work it held up. Focus on how you coordinated the teams and the work that could continue. End with the effect on the study and a lesson for future handoffs.
Question 12: Give an example of how you used test findings to reject a proposed oilfield equipment or process change.
Interviewer tipA strong case links specific test findings to the decision against the proposed change and what happened next. Claiming the change failed without comparing results with its design requirements is weak evidence.
Candidate tipPick a real proposed change. Explain the findings you evaluated, the design requirements they did not meet and your role in rejecting the change. End with the result and what you learned.
Question 13: Explain to me how you simulate reservoir performance for different recovery techniques, using computer models.
Question 14: How do you work through large amounts of production data, well logs and test results to find what matters?
Example answerThe interviewer wants to know whether you have a reliable method for turning a pile of data into decisions. Describe your steps in order, then give one short example. Sample answer: "I start by checking data quality: missing days, unit mix-ups and readings that don't match the field reports. Then I sort wells by what matters for the question, such as decline rate, water cut or pressure trend, and plot them so outliers stand out. I compare the odd wells against their logs and test results to see whether the cause is geology, equipment or measurement. On one field, this showed that several wells with steep declines shared an older completion design, which led us to change the design on the next wells. I write down my assumptions so others can check the work." Pitfalls: listing software without explaining your method, trusting raw data without checks, and giving no example of a decision the analysis supported.
Interviewer tipA strong answer names a repeatable method for cleaning, sorting and flagging data and checking it against the field; trusting raw data without checks is a red flag.
Candidate tipDescribe your steps, the tools you use, how you spot bad data, and give one example where your method turned up a problem or an opportunity.
Question 15: Tell me about a time you used well data to choose between options, such as a completion design, a stimulation treatment or an artificial lift method.
Example answerThe interviewer wants to see how you weigh data, cost and risk to make a sound engineering choice. Use Situation, Task, Action, Result: the well and the problem, the decision you owned, how you compared the options, and how the well performed. Sample answer: "A well on rod pump kept failing as its fluid rate dropped and its gas rate rose. I was asked to recommend a better lift method. I pulled the production history, fluid levels and failure records, and compared rod pump changes, gas lift and plunger lift on expected rates, equipment cost and upkeep. Gas lift fit best because we had gas supply nearby and the well's gas ratio was rising. After the change, failures dropped and production held steadier. Looking back, I would have run the comparison after the first failure instead of the third." Pitfalls: describing the option you picked without the ones you rejected, leaving out cost, and claiming results you can't explain.
Interviewer tipListen for the data they compared, the trade-offs in cost and recovery, and how they checked the result; picking by habit is a red flag.
Candidate tipName the options you weighed, the data and analysis behind your choice, and how the well performed afterward, including anything you would change.
Question 16: Walk me through a time you checked a crew's or contractor's work against a well program and took corrective action.
Example answerThe interviewer wants to learn how you check work against a well program and respond when the work falls short.
Build your answer with Situation, Task, Action, Result. Identify the program and your responsibility for checking the crew's or contractor's work. Explain the records or observations you compared with the plan, the gap you found and your own corrective action. Finish with the follow-up result and a lesson.
For example: "I was checking a contractor's daily work records against the well program. A required equipment check had no recorded result. I asked the supervisor for the supporting record rather than assuming the check had been done. We confirmed it had been missed. I raised the gap with the field supervisor, and the crew completed the check before the affected work resumed. I reviewed the result and recorded the correction. That taught me to check the supporting records before signing off on progress."
Avoid discussing only the well's output, signing off on unverified work or describing a correction without checking whether it resolved the performance gap.
Interviewer tipListen for a clear comparison of actual work with the well program, the candidate's correction, and follow-up. Signing off on work they knew did not meet the program is a red flag.
Candidate tipChoose a real well program. Name the work records or observations you checked against the plan, the performance gap you found, your corrective action, and the result. Include what you learned about checking the work.
Question 17: How do you make the calculations in a well engineering report traceable to the source data?
Interviewer tipA sound answer connects reported results to dated source data, units, assumptions and calculation versions. Unlabeled inputs or overwritten calculations prevent another engineer from checking the report.
Candidate tipTrace a reported result back through the calculations to the well data. Explain how you label sources, units and assumptions so another engineer can reproduce your work.
Question 18: Name a time when you coordinated the installation, maintenance, and operation of mining and oil field equipment.
Question 19: What factors do you consider when testing machinery and equipment to ensure that it is safe and conforms to performance specifications?
Question 20: What is the secret to design and implement environmental controls on oil and gas operations?
Question 21: Walk me through how you would inspect oil and gas wells to determine that installations are completed.
Question 22: Tell me how you made a well test or production forecast report clear for engineering or management readers.
Example answerThe interviewer wants to learn whether you can make technical information understandable and useful to the report's intended readers.
Use Situation, Task, Action, Result for one report you wrote. State who would read it and the decision or engineering work it supported. Explain your choices about organization, terms, charts and supporting detail. Describe feedback or another concrete sign that readers understood it, then identify a lesson you applied to later writing.
For example: "I wrote a production forecast report for managers preparing the field budget. I opened with the expected production range and the assumptions that could change it. I used a labeled trend chart and explained the effect of downtime in everyday language. Detailed calculations went in a supporting section so engineering readers could check them. Before sending it, I asked a colleague to read the summary for unclear terms. In the budget meeting, managers could point to the assumptions they wanted to test. I learned to explain uncertainty near the forecast instead of leaving it in the calculations."
Avoid calling your writing clear without showing your choices. Do not bury key limits or assume management readers understand unexplained engineering terms.
Interviewer tipA strong example shows how they explained well test results or forecast assumptions for the report's readers. Leaving management to interpret unexplained engineering terms is a red flag.
Candidate tipChoose a well test or production forecast report you wrote. Explain its readers and purpose, your choices about charts and technical detail, and the feedback or result that showed its clarity. Include a lesson.
Question 23: Tell me about a time you got geologists, field crews and service contractors working toward one goal on a well or project.
Example answerThe interviewer wants to see how you lead people you may not manage directly and keep a mixed team on one plan. Use Situation, Task, Action, Result: the project, your role, how you aligned each group and the outcome. Sample answer: "On a new horizontal well, the geologist wanted to be able to adjust the landing point late, the rig crew needed a firm plan, and the completion contractor had a tight schedule. I set up a short daily call with all three, shared one updated well plan after each change, and agreed in advance on who would decide if the target moved. When the geologist saw a better zone, we made the change in one call instead of a day of back and forth. The well was landed in the target zone and the completion crew started on time." Pitfalls: making yourself the hero, skipping how you handled disagreements, and leaving out the result.
Interviewer tipListen for how they set a shared plan and kept each group informed; taking credit for the crew's work or ignoring field input is a red flag.
Candidate tipDescribe the project and each group's role, how you kept everyone aligned on the plan and schedule, and how the work turned out.
Question 24: Share an example of how your recommendation on a well, a field plan or a spending decision helped management improve the outcome.
Example answerThe interviewer wants to learn whether your technical advice helps management make better decisions about wells, field plans or spending.
Use Situation, Task, Action, Result to organize one real example. Briefly explain the decision and your responsibility. Spend most of the answer on the evidence, costs and risks you assessed and how you presented your recommendation. Close with management's decision, the observed outcome and what you learned. Separate your contribution from the team's work.
For example: "Our field plan called for starting additional wells before the water-handling system was ready. I compared the startup schedule with expected water volumes and the cost of delaying individual wells. I recommended staging the startups and showed management the capacity limits and trade-offs. Management revised the schedule. We brought the wells online without overloading the water system. I learned to make operating constraints visible alongside the production forecast."
Avoid claiming that management accepted advice you cannot connect to a decision. Do not describe forecast benefits as measured results or omit the costs and risks behind your recommendation.
Interviewer tipA strong example links well data and costs to management's decision and the outcome. Claiming an improvement without checking the results is a red flag.
Candidate tipChoose one recommendation. Explain the well data, costs and risks behind it, your role in management's decision, the result and what you learned.
Question 25: Describe how you handled strong pushback on your plan from a drilling contractor or field supervisor.
Interviewer tipListen for a real disagreement, attention to field concerns and a clear outcome. Dismissing the drilling contractor's or field supervisor's safety concerns without checking them is a red flag.
Candidate tipPick a real disagreement over your plan. Focus on how you heard the field concerns, what you changed or held firm on, the outcome and what you learned about working with the contractor or supervisor.
Question 26: Describe methods you have found effective to take samples to assess the amount and quality of oil, the depth at which resources lie, and the equipment needed to properly extract them.
Question 27: Describe an experience when you supervised the removal of drilling equipment, the removal of any waste, and the safe return of land to structural stability when wells or pockets are exhausted.
Question 28: Tell me about the last time when you conducted engineering research experiments to improve or modify mining and oil machinery and operations.
Question 29: Share an experience in which your attention to detail and thoroughness had an impact on your last company.
Example answerThe interviewer wants proof that you catch errors others miss and that this protects the organization.
Use Situation, Task, Action, Result. Describe what you were checking, what you noticed, and how you found it, such as comparing against a source or double-checking totals. Then explain what would have happened if the error had gone through, and what you did to prevent it next time.
Sample answer: "While preparing an order for a large customer, I compared the quantities against the signed quote, as I always do, and saw that one item had been entered as 1,000 units instead of 100. I flagged it to my supervisor, we corrected it before it shipped, and we avoided a costly return. Afterward I suggested adding a quote-check step to the order form, and the team adopted it."
Pitfalls: Don't just say you're detail-oriented without an example. Avoid exaggerating the dollar impact. Don't describe perfectionism that caused missed deadlines.
Question 30: Provide an example when your ethics were tested.
Example answerThe interviewer wants to know whether you do the right thing when it is inconvenient, and how you handle pressure to cut corners.
Use Situation, Task, Action, Result. Describe the pressure or temptation without naming people, explain the choice you made and why, and how you handled the conversation. Keep the focus on your actions, not on judging others.
Sample answer: "Near the end of a quarter, a coworker asked me to record a sale as complete even though the customer hadn't signed yet, so our numbers would look better. I told them I wasn't comfortable doing that and suggested we tell our manager the deal would close the following week. My manager agreed it should wait. The customer signed early in the new quarter, and our records stayed accurate."
Pitfalls: Don't say your ethics have never been tested. Avoid stories that make you sound self-righteous or that share confidential details. Don't pick an example where you went along with the wrong choice and stop there.