Registered Prosthetic Orthotic Technician Interview Questions
For technicians who make and repair braces, prosthetics, and other medical support devices. Interviews focus on fitting devices to patients, making adjustments, and testing repairs.
30 questions, ranked by what the job needs most
Print the top 10:Scoring sheetPractice sheet
Question 1: Walk me through how you made an orthotic or prosthetic device, from the materials you chose to the finished piece.
Example answerThe interviewer wants to hear that you know the build process and the reasons behind each choice. Walk through it in order: the prescription and model you worked from, the materials and why, how you formed and assembled the device, and how you finished and checked it. Sample answer: "A recent job was a custom spinal brace. I started from the plaster model of the patient's torso and the orthotist's prescription, which called for a rigid shell with a soft lining. I picked a plastic sheet for strength and a foam liner for comfort, heated the sheet and vacuum-formed it over the model. After it cooled I marked the trim lines, cut and ground the edges smooth, riveted on the straps and lined the inside. Before it went out I checked it against the model and the measurements on the order." Pitfalls to avoid: listing materials without saying why you chose them; skipping the finishing and checking steps; describing a device you only watched someone else make.
Interviewer tipLook for a clear sequence, such as working from the cast or model, forming or laminating, trimming and finishing, and why they picked each material; vague steps are a red flag.
Candidate tipPick one device you built, name the materials and tools, explain why they suited the patient, and cover the step that took the most care.
Question 2: Walk me through a repair you made to put a worn brace or prosthesis back in working order.
Interviewer tipListen for a check tied to the fault, such as making sure a replaced brace strap holds. A visual check alone falls short when the fault only shows up during use.
Candidate tipStart with the wear or damage that brought the device in. Describe the part you replaced or adjusted and the check that showed whether the repair solved the original problem.
Question 3: Recall a time when you caught a small but important mismatch between a work order and a brace or prosthesis.
Interviewer tipA strong example names the detail they caught and what the check changed. Sending a device on with a known mismatch because it looked fine is a red flag.
Candidate tipName the specific mismatch, such as the side listed or the part called for. Say what you checked against the work order and what changed before the device went out.
Question 4: How do you turn a brace prescription into a list of materials and tools needed for fabrication?
Interviewer tipA sound answer connects the brace design, dimensions and specified materials to the stock and tools needed. Choosing materials without checking the prescription is a red flag.
Candidate tipWalk through reading the brace prescription, identifying the material specifications and matching each fabrication step to the tools it needs. Explain the checks that keep your list tied to the prescribed design.
Question 5: Tell me how you checked that a patient's limb cast or impression was accurate enough to make a custom brace.
Interviewer tipListen for how they checked the cast for the shape and detail needed for a good brace fit. Building from a cast with a distorted area that affects the fit is a red flag.
Candidate tipUse a cast or impression you made or received. Describe which feature the brace needed to fit, such as the shape around the ankle, and what you checked before using the cast.
Question 6: Describe how you checked the alignment and movement of a hinged brace before handing it off for fitting.
Interviewer tipA strong example covers hinge position and how the brace moves. Flag a description that treats a straight-looking brace as ready even when the hinge binds.
Candidate tipName the reference you used for hinge position and describe what you felt or saw as you moved the brace through its intended range. If it needed an adjustment, say what the next check showed.
Question 7: Give an example of how you finished a custom brace edge with a grinding or buffing wheel.
Interviewer tipListen for a check of both edge smoothness and shape. Grinding past the intended edge just to remove a nick is a red flag.
Candidate tipName the brace material and the edge finish you needed. Describe how you used the wheel and checked that the edge was smooth and still followed the intended outline.
Question 8: How have you formed a plastic brace shell over a model of a patient's limb?
Interviewer tipListen for how they got the plastic to follow the model around tight curves. Removing the shell while it can still lose its shape is a red flag.
Candidate tipUse one brace shell to explain how you got the plastic to follow the limb model around a tight curve. Say how you checked that the shell held its shape after it cooled.
Question 9: How do you lay out and mark the cut lines for a brace upright from a drawing?
Interviewer tipA good answer uses a fixed reference point from the drawing and checks where the cut will land. Measuring from an unverified mark can carry an error into the rest of the layout.
Candidate tipName the point on the drawing you measure from. Explain how you transfer the dimensions to the upright, the rigid side support, and check the cut marks against the drawing.
Question 10: Share an example of how you attached a metal side support to a brace shell using drilled holes and fasteners.
Interviewer tipListen for how they kept the parts from shifting and checked the finished joint. Forcing a fastener through mismatched holes is a red flag.
Candidate tipDescribe how you held the side support in place while drilling and chose a fastener for the shell. End with how you checked that the joint was secure.
Question 11: Share an experience in which you covered and padded metal and plastic structures.
Question 12: Describe a time you found and fixed a mechanical fault in a device, such as a worn prosthetic knee joint or a sticking brace hinge.
Example answerThe interviewer wants to see how you trace a mechanical fault and confirm the repair. Use Situation, Task, Action, Result: the device and the symptom, how you found the cause, what you repaired and how you tested it. Sample answer: "A patient reported that their prosthetic knee clicked and felt loose when they stood up. On the bench I worked the joint through its range and found play at the axle. The bushings were worn and one fastener had backed out. I checked the manufacturer's specifications, replaced the bushings, tightened the fastener to the specified torque and ran the joint through its full range again. Then I checked the alignment in the fixture before the device went back for the clinician to fit." Pitfalls to avoid: replacing parts at random until the noise stops; skipping the specifications or the test afterward; claiming repairs on components you aren't trained or allowed to service.
Interviewer tipListen for how they traced the fault, followed the specifications and tested the part after the repair; swapping parts until something works is a red flag.
Candidate tipName the device and the fault, how you found the cause, what you repaired or replaced, and how you tested it before it went back to the patient.
Question 13: Tell me about a time you inspected a worn or broken brace or prosthesis and found what caused the problem.
Example answerThe interviewer wants to see how you find the cause of a failure, not only the damage. Use Situation, Task, Action, Result: the device that came in, what you inspected, how you worked out the cause and what you did about it. Sample answer: "A patient's knee brace came back with a cracked upright for the second time in a few months. Instead of only replacing it, I looked over the whole brace. The hinge on the other side was stiff, so one upright was taking most of the load each time the knee bent. I cleaned and adjusted the hinge, replaced the cracked upright and checked that both sides moved together. I also wrote up what I found for the orthotist so they could ask the patient how the brace was being used." Pitfalls to avoid: describing the damage without the cause; skipping a test after the repair; guessing at how the patient used the device instead of passing the question to the clinician.
Interviewer tipStrong answers describe what they checked, such as cracks, loose rivets or worn padding, and how they tied the damage to a cause; fixing only the symptom is a red flag.
Candidate tipWalk through what you looked at, what you found, how you worked out the cause, and what you did so it would not happen again.
Question 14: Walk me through how you adjusted a brace or prosthesis while fitting it on a patient.
Example answerThe interviewer wants to learn how you use patient feedback and fit checks to make a brace or prosthesis fit better.
Build your answer with Situation, Task, Action, Result. Briefly describe the device and fit problem, then explain your responsibility during the fitting. Spend most of the answer on your checks and adjustments. End with the fit afterward and what you learned. Make clear which work you did and where the orthotist or prosthetist directed the adjustment.
For example: "During a brace fitting, the patient reported rubbing near the ankle. My task was to adjust the brace with the orthotist's direction. I checked where the rubbing occurred and adjusted the edge as directed. We checked the area again with the brace on, and the patient reported that the rubbing had stopped. I learned to ask about specific spots instead of relying on a general question about comfort."
Avoid describing an adjustment without checking its effect. Don't treat patient feedback as a substitute for fit checks or claim work that someone else performed.
Interviewer tipListen for the technician's own fit checks, adjustments and result, plus what they learned. Leaving a known pressure point unresolved is a red flag.
Candidate tipChoose one real fitting. Describe the patient's fit problem, the adjustment you made and the checks afterward, then end with the result and what you learned.
Question 15: Share an example of how you chose the information to use from several sources when a device prescription or work order was unclear.
Example answerThe interviewer wants to learn how you sort useful information from several sources before building a device from an unclear order.
Use Situation, Task, Action, Result. Identify the unclear detail and your responsibility. Explain which sources you checked, what each could tell you and why some information did not resolve the issue. Describe any clarification you sought, then give the result and what you learned about checking orders.
For example: "A brace work order had an unclear trim line. I needed a clear specification before cutting. I checked the order, cast markings and measurements. The measurements helped confirm that the cast matched the order, but they could not settle the trim line. I asked the orthotist to clarify that point and recorded the answer on the work order before cutting. That let me build to the intended shape. I learned to separate information that identifies the device from information that specifies its construction."
Avoid merely listing sources without explaining their relevance. Don't guess at unclear specifications or present your own preference as the clinician's instruction.
Interviewer tipListen for how they weighed the work order, measurements or cast and clarified gaps with the orthotist or prosthetist. Guessing at an unclear device specification is a red flag; ask what they learned.
Candidate tipPick a real unclear device order. Explain which sources you compared, how you chose what applied and what you clarified before building. Finish with the result and a lesson for checking future orders.
Question 16: Describe a time you handled a delay in getting parts or supplies needed to finish an orthotic or prosthetic device.
Interviewer tipListen for their own steps to confirm availability, follow up with the supplier and update the lab's build schedule. Promising a delivery date without checking with the supplier is a red flag.
Candidate tipChoose one delayed parts or supplies order. Explain the device it held up, what you did with the supplier and the lab, and the result. Include one ordering habit you changed afterward.
Question 17: Tell me about a time you had to tell a clinician or patient that a device would be late or could not be made as ordered.
Interviewer tipStrong answers show they spoke up early, explained the reason plainly and offered options; waiting until the due date or hiding the problem is a red flag.
Candidate tipExplain what the problem was, who you told and when, how you put it, and what you offered to keep the patient's care on track.
Question 18: Tell me about a time you learned to use a new piece of lab equipment, such as a digital scanner or a vacuum-forming machine.
Example answerThe interviewer wants to know how you learn new equipment safely and get reliable results from it. Use Situation, Task, Action, Result: what the equipment was, how you learned it, what went wrong or surprised you, and how you checked your work. Sample answer: "Our lab bought a new vacuum-forming machine, and its controls and heating times were different from the old one. I read the manual, then had the lab supervisor walk me through the first few runs. My first practice piece came out thin on one side because the sheet sagged too long in the oven, so I logged the heating time and sheet thickness for each run until I had settings that worked. After that I wrote a short settings sheet that others in the lab started using." Pitfalls to avoid: saying you learned it without any training or help; skipping the safety steps; leaving out how you knew the results were good.
Interviewer tipA strong answer shows how they learned safely, through manuals, training or supervised practice, and checked their first results; skipping safety steps to save time is a red flag.
Candidate tipName the equipment, how you learned it, a mistake or surprise along the way, and how you knew your work with it met the standard.
Question 19: Tell me how you used a new technology or method in an orthotics or prosthetics lab to improve devices for patients.
Interviewer tipLook for their own work introducing the lab method, a checked result for patients and a lesson learned. Claiming a better fit without checking the finished device is a red flag.
Candidate tipChoose a real lab change, such as a scanning method or material. Describe how you learned and used it, what you observed in the patient devices and what you learned from the result.
Question 20: Describe your experience mixing pigments to match patients' skin coloring.
Question 21: Share an experience in which you effectively repaired machinery used in the fabrication of appliances.
Question 22: Share an effective method you have used to instruct patients in the use of prosthetic and orthotic devices. Provide an experience.
Question 23: Tell me about a time when you successfully determined the cause of an operating error at your company and solved the problem.
Example answerThe interviewer wants to see how you track down the real cause of a problem instead of treating only the symptoms.
Use Situation, Task, Action, Result. Describe the error and its impact, the steps you took to narrow down the cause, the fix, and what you did to keep it from happening again.
Sample answer: "Our label printer started putting the wrong dates on some product labels, which meant those items had to be pulled from the shelves. I checked the printer settings first, and they were fine. Then I compared the bad labels and saw they all came from orders entered after a software update. The update had changed the date format in one field. I worked with our IT contact to fix the setting, reprinted the labels, and added a quick label check to our start-of-shift routine."
Pitfalls: Don't stop at the first fix that seemed to work. Avoid blaming coworkers. Don't leave out how you prevented a repeat.
Question 24: Share an experience in which you conducted a test of a product, service, or process and successfully improved the quality or performance.
Example answerThe interviewer wants evidence that you test things carefully and use what you find to make them better.
Use Situation, Task, Action, Result. Explain what you tested and why, how you set up the test, what the results showed, and what you changed. End with how you measured the improvement.
Sample answer: "Customers kept saying our online order form was confusing, so I was asked to look into it. I had five coworkers who had never used the form place a test order while I watched and took notes. Four of them got stuck on the same shipping step. I suggested moving that step and rewording two labels, then ran the same test again. All five finished without help, and complaints about the form dropped over the next month."
Pitfalls: Don't describe a change made on a hunch with no test. Avoid skipping how you checked the result. Don't use jargon without explaining it.
Question 25: Provide an example when your ethics were tested.
Example answerThe interviewer wants to know whether you do the right thing when it is inconvenient, and how you handle pressure to cut corners.
Use Situation, Task, Action, Result. Describe the pressure or temptation without naming people, explain the choice you made and why, and how you handled the conversation. Keep the focus on your actions, not on judging others.
Sample answer: "Near the end of a quarter, a coworker asked me to record a sale as complete even though the customer hadn't signed yet, so our numbers would look better. I told them I wasn't comfortable doing that and suggested we tell our manager the deal would close the following week. My manager agreed it should wait. The customer signed early in the new quarter, and our records stayed accurate."
Pitfalls: Don't say your ethics have never been tested. Avoid stories that make you sound self-righteous or that share confidential details. Don't pick an example where you went along with the wrong choice and stop there.
Question 26: Share an example of when you went above and beyond the "call of duty".
Interviewer tipLook for answers that show the candidate is dependable.
Candidate tipThe employer wants to know that you are dependable.
Question 27: Tell me how you organize, plan, and prioritize your work.
Example answerThe interviewer wants to understand your system for managing work, and whether it holds up when priorities change.
Describe the method you actually use, step by step, then back it with a short example. Cover how you capture tasks, how you decide what comes first (deadlines, impact, who is waiting on you), and how often you review the plan. Mention what you do when something urgent comes in.
Sample answer: "I keep one task list and review it every morning. I sort tasks by deadline and by who depends on them, and I block time on my calendar for the two or three most important ones. At the end of the week I look at what slipped and why. Last month a rush request came in mid-week, so I checked with my manager about which existing task could move, shifted it, and told the person affected right away."
Pitfalls: Don't give a vague answer like 'I'm very organized.' Avoid naming tools without explaining how you use them. Don't describe a system that has no way to handle changes.
Candidate tipBe sure to mention that you make specific goals.
Question 28: Provide an experience that demonstrates your ability to manage time effectively. What were the challenges and results?
Example answerThe interviewer wants to know how you plan your time and handle competing demands, and whether you meet deadlines.
Use Situation, Task, Action, Result. Name the specific challenges, such as overlapping deadlines or interruptions. Describe the steps you took to plan and protect your time, and what you did when something came up. End with the results the question asks for.
Sample answer: "During one busy week, I had a report due Thursday, two new team members to train, and my usual daily tasks. I mapped out the week on Monday, scheduled training for the mornings when things were quieter, and blocked two afternoons for the report. When an urgent request came in Wednesday, I asked a colleague to cover one training session. The report went in a day early, and both new team members finished their training on schedule."
Pitfalls: Don't just list time-management tools. Avoid a story where you met the deadline only by working through the night. Don't skip the challenges.
Question 29: Describe a time when you were able to select the best tool to do a job. How did you use reasoning skills to make the best choice?
Example answerThe interviewer wants to see how you think through a choice of tool or equipment instead of using whatever is closest.
Use Situation, Task, Action, Result. Describe the job, the options you had, the factors you weighed (safety, the material, precision, time, and cost), and how your choice worked out.
Sample answer: "I needed to drill holes in a set of thin metal brackets without bending them. The quickest option was a hand drill, but it would be hard to keep the holes straight, and the metal could warp. I chose the drill press with a clamp and a bit made for metal, and I used a slower speed and cutting oil. Every hole came out clean and lined up, and none of the brackets had to be redone."
Pitfalls: Don't describe your choice without the reasons behind it. Avoid stories where you skipped safety to save time. Don't forget to say how the choice worked out.
Question 30: Tell me about your last experience doing repair work. How did you determine what tools you needed?
Example answerThe interviewer wants to see how you plan a repair, including choosing the right tools, so the job is done safely and well.
Use Situation, Task, Action, Result. Describe the repair, how you figured out what was wrong, how you decided on tools and parts (the manual, the fasteners involved, what you saw during inspection), and how the repair turned out.
Sample answer: "A door closer at our building's entrance was letting the door slam. I checked the manual for that model and learned the speed valves needed a small hex key, and that a leaking closer would need replacing instead. I looked for oil around the body, saw none, and brought the hex key, a step ladder, and a rag. I adjusted the closing and latch speeds a little at a time and tested the door after each turn. It closed smoothly, and I noted the settings in our maintenance log."
Pitfalls: Don't describe grabbing whatever tool was nearby. Avoid skipping how you tested the repair. Don't forget to answer the tools part of the question.
New to interviews? Start with the common questions every interview asks →