Skip to content

Designer Interview Questions

For drafters who prepare drawings for electronic equipment. Interviews focus on turning circuit designs into schematics and assembly drawings that production teams can use.

30 questions, ranked by what the job needs most

Also for Designer: Multimedia Artists and Animators · Mechanical Engineering Technicians · Commercial and Industrial Designers · all 18 sets →

Print the top 10:Scoring sheetPractice sheet

  1. Question 1: Describe a time you prepared the detail and assembly drawings for a circuit board build.

  2. Question 2: How do you show both ends of a cable on a wiring diagram so an installation crew can connect it correctly?

  3. Question 3: Share an example of an error or wrong revision you caught in an electronics drawing before it reached assembly.

  4. Question 4: Tell me how you worked with an engineer to settle a missing requirement in a markup or sketch before finishing a drawing.

  5. Question 5: Share an example of how you assembled an engineer's review package when its drawings and supporting documents had different revision dates.

  6. Question 6: How do you distinguish a component's physical orientation from its electrical connections in an electronic assembly drawing?

  7. Question 7: Tell me about a time you changed a logic element's layout while preserving the connections shown in the engineer's schematic.

  8. Question 8: Walk me through a time you used a schematic and component data sheets to work out the specifications for a wiring drawing.

  9. Question 9: How do you work out the allowed range for a dimension given as a nominal value with a tolerance on an electronic part drawing?

  10. Question 10: What do you check in a vendor's proposed replacement connector before updating an electronic assembly drawing?

  11. Question 11: Describe a time you helped engineering and assembly staff agree on a fix for an electronic part that would not fit.

  12. Question 12: Give an example of how you sorted out conflicting information in a schematic, an engineer's redlines and part datasheets.

  13. Question 13: Share an example of how you kept an installation crew working from the right drawing after a field adjustment.

  14. Question 14: Walk me through a time you used a scaled layout to check whether proposed electronic equipment would fit around existing equipment.

  15. Question 15: Share an example of how you measured a cable route that could not be checked in one straight line.

  16. Question 16: What would you do if an assembler proposed a shorter conductor path that broke a separation requirement on the customer's drawing?

  17. Question 17: Give an example of how you caught a mismatch between a wiring installation drawing and its cost estimate.

  18. Question 18: How do you check that a drawing set meets your company's drafting standards and any codes that apply before it goes to the engineer for sign-off?

  19. Question 19: Describe a time you helped an engineer compare the drawing changes needed for two design options.

  20. Question 20: Describe a time you clarified whether an installation work order needed power wiring, signal wiring or both.

  21. Question 21: What would you do if an added piece of electronic equipment would exceed the available power circuit capacity?

  22. Question 22: Recall a time you recovered a project drawing that was missing from its expected library location.

  23. Question 23: What do you check on a printed copy of a scaled equipment drawing before giving it to an installation crew?

  24. Question 24: Provide an experience in which you successfully located files and recorded job completion data.

  25. Question 25: Describe how you helped an assembler, technician or installation crew follow one of your drawings when they found it confusing.

  26. Question 26: Share an experience in which conferring with vendors or design staff helped you to resolve a problem or improve a design.

  27. Question 27: Provide an experience in which reviewing blueprints and consulting with an assembler helped you effectively meet customer requirements.

  28. Question 28: Talk about a time you put a newly learned CAD or ECAD tool, part library or drafting standard to use on a drawing.

  29. Question 29: Share an example of the extra steps you took to deliver a complete, correct drawing set when your project team faced a hard deadline.

  30. Question 30: Tell me about a time you had to tell an engineer or project lead that a drawing package would be late or that their design had a problem.