Skip to content

Propulsion Motor and Generator Repairer Interview Questions

For mechanics who repair electric motors and power tools. Interviews focus on diagnosing faults with electrical meters and reassembling motors to specifications.

30 questions, ranked by what the job needs most

In other fields: Automotive Master Mechanics · compare them →

Propulsion Motor and Generator Repairer in 1 other field →

Print the top 10:Scoring sheetPractice sheet

  1. Question 1: Walk me through how you use meters such as a clamp meter, multimeter or tachometer to find out why a motor is drawing too much current.

  2. Question 2: How do you use the work order and your own tests to figure out why a power tool keeps cutting out?

  3. Question 3: What's the trickiest part of reassembling a repaired electric motor to its specifications?

  4. Question 4: How do you use a wiring diagram to check the connections in a generator's battery charging circuit?

  5. Question 5: Walk me through how you repair a generator shaft after a worn bearing damages it.

  6. Question 6: Walk me through a time you took apart a motor or power tool with a part that was hard to remove.

  7. Question 7: What's the trickiest part of lifting a heavy electric motor with a chain hoist?

  8. Question 8: Share an example of a motor or power tool repair record that helped someone understand the work you had done.

  9. Question 9: Describe a time you restored a motor or power tool's operation by adjusting a contact or spring.

  10. Question 10: Explain how you decided on the work and timing for the last preventive maintenance you did on a motor or generator.

  11. Question 11: How do you decide which lubricant and how much to use on a motor bearing that needs lubrication?

  12. Question 12: Tell me about a time a service guide changed the way you carried out a motor or power tool repair.

  13. Question 13: How do you choose a cleaning method for a motor part with oil and dirt on it?

  14. Question 14: What would you do if nearby insulation started scorching while you were soldering a motor lead?

  15. Question 15: What kind of experience do you have assembling electrical parts such as alternators, generators, starting devices, and switches, following schematic drawings and using hand, machine, and power tools? Share an example.

  16. Question 16: Walk me through a mechanical fault you repaired in an electric motor or power tool.

  17. Question 17: Tell me how you chose the tools and test equipment for the last motor or power tool you repaired.

  18. Question 18: Describe a time you repaired or tested the electronic controls on a motor or tool, such as a speed control board, a drive or a battery charger.

  19. Question 19: Share an example of how you weighed conflicting information from a customer, a service manual and your tests during a motor or power tool repair.

  20. Question 20: Tell me about a time you went beyond what was expected to get a customer's motor or equipment back in service.

  21. Question 21: Tell me about a time you had to tell a customer that their motor or tool would cost more to repair than to replace.

  22. Question 22: Describe how you handled a customer who was upset about a motor or power tool repair's cost or delay.

  23. Question 23: Describe how you learned to run a new piece of shop equipment, such as a coil winder, surge tester or balancing machine.

  24. Question 24: Tell me about a time your attention to detail caught a mistake in a motor repair, such as a wrong connection, a missed spec or a worn part.

  25. Question 25: Tell me about an experience in which you analyzed information and evaluated results to choose the best solution to a problem.

  26. Question 26: Share an experience in which your diligence of inspecting equipment, structures, or materials helped you identify a problem or the cause of a problem.

  27. Question 27: Provide an example when your ethics were tested.

  28. Question 28: Tell me how you organize, plan, and prioritize your work.

  29. Question 29: How do you balance cooperation with others and independent thinking? Share an example.

  30. Question 30: Describe a time when you were able to select the best tool to do a job. How did you use reasoning skills to make the best choice?