Skip to content

Stage Rigger Interview Questions

For general construction carpenters who work on frames, floors and fixtures. Interviews focus on reading plans, laying out work and estimating costs.

30 questions, ranked by what the job needs most

Also for Stage Rigger: Riggers · compare them →

Print the top 10:Scoring sheetPractice sheet

  1. Question 1: Describe a time you laid out matching cuts in lumber without letting small measuring errors add up.

  2. Question 2: Walk me through how you read a set of plans before you start layout, from checking dimensions to working out the materials you need.

  3. Question 3: Walk me through a window installation where the opening needed adjustment before the window would fit.

  4. Question 4: Walk me through how you measure, mark and cut a piece to an exact fit, such as a trim miter or a stair stringer.

  5. Question 5: How do you keep up with jobsite safety rules for your cutting area, from setting up the saw to clearing wood scraps?

  6. Question 6: How do you check that a level is giving a true reading before you use it to check framing?

  7. Question 7: Talk about a time you brought a frame back to square during assembly.

  8. Question 8: Walk me through how you built or repaired a cabinet, door, stair or other wood fixture with woodworking machines, hand tools or power tools.

  9. Question 9: What do you allow for when building a solid wood cabinet door so seasonal wood movement does not cause problems?

  10. Question 10: Talk about a time you kept a rough door opening at the required size while securing its framing.

  11. Question 11: Tell me about a time you changed your cutting setup to stop a wood edge from splintering.

  12. Question 12: Share an example of how you resolved a lumber delivery with a different grade stamp from the grade you ordered.

  13. Question 13: What is the challenging part of selecting and ordering lumber or other required materials? How did you succeed?

  14. Question 14: Give an example of how you removed a damaged section of woodwork without damaging the sound pieces beside it.

  15. Question 15: Walk me through how you inspect trim, siding, flooring or other woodwork for damage before a repair.

  16. Question 16: What would you do if a repair inspection revealed a loose, cracked window pane above an occupied walkway?

  17. Question 17: What would you do if you found deep decay in a load-bearing timber while preparing to replace it?

  18. Question 18: What would you do if a brace came loose on a concrete form you were preparing for a pour?

  19. Question 19: What would you do if the ground where you need to erect a scaffold for exterior carpentry is soft or uneven?

  20. Question 20: What moisture checks do you make before laying hardwood flooring over a wood subfloor?

  21. Question 21: Share an example of how you prepared woodwork with an uneven surface for a smooth painted finish.

  22. Question 22: Describe a time you corrected a drywall patch that still showed through after sanding.

  23. Question 23: How do you keep drilled bolt holes aligned when a connection passes through more than one timber?

  24. Question 24: How do you lay out post holes so the finished posts will line up at the required spacing?

  25. Question 25: How do you keep offcuts, loose nails and sawdust from making your carpentry work area unsafe as the job progresses?

  26. Question 26: Give an example of extra effort you put into your carpentry work to keep other trades from being held up.

  27. Question 27: Tell me how you compared possible fixes for a wall out of plumb, a beam that didn't fit or another carpentry problem on site.

  28. Question 28: Tell me about a time you had to tell a client or supervisor about a problem you found, such as rot or framing out of square, that would add time or cost.

  29. Question 29: Walk me through how you prepare a cost estimate for a carpentry job, from takeoff to the number you give the client.

  30. Question 30: Walk me through a time you revised a carpentry estimate after the client changed the scope.