Skip to content

Heavy Truck Mechanic Interview Questions

For diesel mechanics who service buses and trucks. Interviews focus on inspecting brakes and steering and using road tests to diagnose faults or verify repairs.

30 questions, ranked by what the job needs most

Also for Heavy Truck Mechanic: Automotive Master Mechanics · compare them →

Print the top 10:Scoring sheetPractice sheet

  1. Question 1: Walk me through how you check the brakes, steering and wheel bearings on a truck or bus before it goes back into service.

  2. Question 2: What do you find most challenging about diagnosing a diesel engine problem using a scan tool, gauges and your own ears?

  3. Question 3: What checks do you make before the first start of a rebuilt diesel engine?

  4. Question 4: What would you do if you found a bulge in a truck tire's sidewall while preparing to remove it?

  5. Question 5: Walk me through how you reline and adjust the brakes on a heavy truck or bus.

  6. Question 6: Walk me through the hand and power tools you rely on most when working on heavy trucks and diesel engines.

  7. Question 7: Describe a time you used a hydraulic jack or hoist to lift a bus, truck or heavy component for a repair.

  8. Question 8: Tell me about a time you test-drove a truck or bus to track down a problem or confirm a repair.

  9. Question 9: Share an example of how you repaired a diesel exhaust aftertreatment fault that kept returning.

  10. Question 10: How do you replace a damaged section of a truck's lighting harness so the repair holds up to vibration and road spray?

  11. Question 11: Describe an experience where you attached test instruments to equipment, and read dials and gauges to diagnose malfunctions.

  12. Question 12: Walk me through a repair you made to a truck's air compressor when it was not building enough pressure.

  13. Question 13: Describe a time you repaired a truck or bus cab heater that was not warming the cab.

  14. Question 14: What would you do if a truck was ready to leave the shop but its fan shroud could not be secured?

  15. Question 15: Talk about a time you corrected uneven tire wear by aligning a truck's front end.

  16. Question 16: What have you found to be the best way to Inspect and verify dimensions and clearances of parts to ensure conformance to factory specifications?

  17. Question 17: Walk me through how you disassemble and overhaul internal combustion engines, pumps, generators, transmissions, clutches, and differential units.

  18. Question 18: Tell me about a time you removed a stuck diesel fuel injector.

  19. Question 19: How do you decide whether a worn diesel engine valve can be reconditioned or needs replacement?

  20. Question 20: Share your knowledge with maintaining or repairing vehicles with alternative fuel systems, including biodiesel, hybrid, or compressed natural gas vehicles. Share an example.

  21. Question 21: Describe a time you repaired a bus door that would not close properly.

  22. Question 22: Give an example of how you fitted an accessory to a truck when the mounting space was tight.

  23. Question 23: Walk me through your process for a routine preventive maintenance service on a heavy truck or bus.

  24. Question 24: Describe a time you used test results to choose a repair for a truck or bus problem with several possible causes.

  25. Question 25: Tell me about a time you tracked down a fault in a truck's electronic controls, such as an engine control module, a sensor or a wiring harness.

  26. Question 26: Describe a time a careful final check of your own truck or bus repair caught a mistake before the vehicle left the shop.

  27. Question 27: Tell me about a time a careful inspection of a truck or bus caught a problem before it caused a breakdown or a safety issue.

  28. Question 28: Tell me about a time you had to learn a new diagnostic tool, software or engine system, such as a newer emissions system, and put it to use in the shop.

  29. Question 29: Tell me how you organize, plan, and prioritize your work.

  30. Question 30: Provide an example when your ethics were tested.