Skip to content

Boiler Setter Interview Questions

For boilermakers who build and repair boilers and pressure vessels. Interviews focus on using blueprints to fit parts, rigging heavy sections and replacing faulty valves.

30 questions, ranked by what the job needs most

Print the top 10:Scoring sheetPractice sheet

  1. Question 1: Walk me through how you'd use an assembly drawing to line up and secure a steel section on a boiler frame.

  2. Question 2: Share an example of a time you caught a mismatch between a boiler drawing and the parts at the job site.

  3. Question 3: How would you attach the lifting gear and signal the crane operator to move a boiler plate section into place?

  4. Question 4: What would you do if the pressure gauges on a boiler showed different readings before you began a pressure test?

  5. Question 5: Describe a time you inspected a boiler or pressure vessel to find a defect that needed repair.

  6. Question 6: What do you check to confirm a replacement boiler valve matches the specifications and has no defects?

  7. Question 7: Walk me through a time you had trouble getting a boiler tube end joint to seal.

  8. Question 8: Tell me about a time you repaired or replaced a defective part on a boiler or pressure vessel, such as a safety valve or regulator.

  9. Question 9: What do you check in the welding procedure before arc welding pressure vessel parts together?

  10. Question 10: Share an example of how you laid out a steel plate for a boiler part, marking where it needed to be cut and bent.

  11. Question 11: What method have you found useful to locate and mark reference points for columns or plates on boiler foundations, following blueprints and using straightedges, squares, transits, or measuring instruments?

  12. Question 12: Describe a time you had to shape a seam, joint, or irregular edge on a vessel section so the parts would fit as specified.

  13. Question 13: What kind of experience do you have shaping or fabricating parts, such as stacks, uptakes, or chutes, to adapt pressure vessels, heat exchangers, or piping to premises, using heavy-metalworking machines such as brakes, rolls, or drill presses?

  14. Question 14: What is the most challenging part of Installing manholes, handholes, taps, tubes, valves, gauges, or feedwater connections in drums of water tube boilers, using hand tools? Share an experience.

  15. Question 15: Tell me about a time you straightened a bent structural part on a boiler to match the drawing.

  16. Question 16: Describe a time you removed a stubborn deposit from boiler equipment without damaging the surface underneath.

  17. Question 17: Tell me about a time a careful inspection of a boiler tube, weld, or fitting helped you find a problem or its cause.

  18. Question 18: Describe how you responded to a problem you spotted while monitoring a pressure test on a boiler or vessel.

  19. Question 19: Describe a time you serviced, repaired, or tested a boiler auxiliary or fitting, such as a feedwater pump, fan, or water column.

  20. Question 20: Tell me about a time you had to tell a foreman or inspector that a weld, fit-up, or repair didn't pass or would run late.

  21. Question 21: Share an experience in which your attention to detail and thoroughness had an impact on your last company.

  22. Question 22: Tell me about your experience operating equipment used on boiler jobs, such as aerial lifts, forklifts, chain hoists, or welding machines.

  23. Question 23: How do you manage climbing, working in tight spaces, and working in heat throughout a long boiler work shift?

  24. Question 24: Share the difficulties when assembling large vessels in an on-site fabrication shop prior to installation to ensure proper fit.

  25. Question 25: Share an example where you had to Install refractory bricks or other heat-resistant materials in fireboxes of pressure vessels.

  26. Question 26: Share an experience in which you conducted a test of a product, service, or process and successfully improved the quality or performance.

  27. Question 27: Tell me about the last time you performed routine maintenance on equipment. How did you determine when and what type of work was needed?

  28. Question 28: Tell me about your last experience doing repair work. How did you determine what tools you needed?

  29. Question 29: Provide an example of a time when you were able to demonstrate excellent listening skills. What was the situation and outcome?

  30. Question 30: How do you balance cooperation with others and independent thinking? Share an example.